Base Material for Replacement Leg Kit for etrailer RV Dinette Tables

Question

Question:

You say the legs are metal, but are the base components metal or plastic? Thx!

asked by: Lester W

0

Expert Reply:

Hey Lester,

I just ran out to our warehouse and confirmed that the base pieces of the Replacement Leg Kit # e79RR are also made of metal.

expert reply by: Jon G

0

Lester W.

10/30/2024

Thank you Jon!

Answer 1

Hey Richard, thanks for reaching out. The base bracket included with the Replacement Leg Kit for etrailer RV Dinette Tables #e79RR is approximately 2-1/4" tall. I've included a picture with detailed dimensions for your reference. What camper…

view full answer...

Answer 2

Hey Bianca, it does sound like what you are looking for is the Replacement Lower Sidewall Vent part #DMC22WF which is the door and the frame that you are looking for. Is your current RV fridge a Dometic Americana II?

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Base Material for Replacement Leg Kit for etrailer RV Dinette Tables

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching