Replacement Wiring Harness for Redarc Tow-Pro Elite Brake Controller

Question

Question:

Hello, Im looking for a replacement wiring harness for Redarc Tow Pro Liberty remote switch. Are these available? Thanks for your time.

asked by: Terry M

0

Expert Reply:

Hey Terry, thanks for reaching out!

What you're needing is the Redarc Tow-Pro Elite Control Knob Wiring Harness # RED58FR.

expert reply by: Jon G

0

Kate F.

12/22/2025

Hey Terry, did the Redarc Tow-Pro Elite wiring harness end up working with your Tow-Pro Liberty remote switch? Knowing how it fit could help others trying to match these parts.

Answer 1

Redarc does not offer longer cables between the knob and the module but we've spoken with Redarc before and they have told us that you can use a standard RJ45 network cable to extend as far as needed which you'd be able to easily source…

view full answer...

Answer 2

For a 12,000 lb. electric car trailer winch like the Bulldog Winch Trailer Winch part #BDW10040, I recommend a standard 12 volt lead acid battery rated up to at least 650 cold cranking amps (CCA). As long as the battery is rated up to 650 CCA then…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Yes, we can sell the front tie downs separately. For your 2024 Ford F350 short bed, the correct front TorkLift tie downs are part #TL77CR, as long as your truck's hitch has open ends on the cross tube. Based on the information you provided, this…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Jacob, thanks for the information! I have three options for frame mounted camper tie downs that will fit your 2015 Chevy Silverado 2500HD with an 8' bed and full length running boards. Which set you need is going to depend on what kind of…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Replacement Wiring Harness for Redarc Tow-Pro Elite Brake Controller

Product Page this Question was Asked From

Continue Researching