Screw Size Included with the Tekonsha Replacement Mounting Bracket # 2178

Question

Question:

What size are the screws to hold brake into the bracket, I lost mine. Thank you.

asked by: Jay

1

Helpful Expert Reply:

The screws are pretty small, I went out into our warehouse and pulled the Tekonsha Replacement Mounting Bracket # 2178 to measure the screws for you and found them to be 1/2 inch long, 1/8 inch in diameter and would use a 1/4 inch wrench or socket to tighten.

expert reply by: Jameson C

1

Answer 1

Hi Thomas; the Coil SumoSprings are pretty universal so they may fit. They're only listed for 2WD because SuperSprings never tested them on AWD models. The fact that the Timbren is listed as a fit for both does imply they will likely work, but I…

view full answer...

Answer 2

The #CSS-1168R and #CSS-1195F are only confirmed to fit the FWD models but that doesn't mean there aren't Coil SumoSprings for your 2023 Sienna AWD. To find the right size you will need to measure the gap between in the middle of the coil.…

view full answer...

Answer 3

Doing a quick parts search I do see the rear coil springs on a 2WD 2024 Toyota Sienna are the same as on a AWD 2024 Toyota Sienna. So unless you have something else inside your coils you should not have any fitment issues with the Coil SumoSprings…

view full answer...

Answer 4

Hey William, yes we do have a replacement mounting bracket for the P3 part #90195 with the part #TK5906. Did yours break?

view full answer...

Answer 5

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Screw Size Included with the Tekonsha Replacement Mounting Bracket # 2178

Continue Researching