Availability of Pictures or Video Installation of BAK Revolver X4s on 2018 Nissan Titan

Question

Question:

2018 titan platinum 5 1/2 ft bed with util track and titan tool boxes. Are there any pics or videos of installation of the bak revolver s for this truck. Mainly concerned as to how to attach rails to bed with the tracks?

asked by: Dave B

0

Expert Reply:

HI Dave; we don't have any specific pictures or videos for the 2018 Nissan Titan, or similar models that show this with the BAK Revolver X4s # BAK68ZR. However, I can confirm that the tonneau cover will fit if you have the Utili-Track system. This has also been verified by the manufacturer. The best I can offer is the installation instructions for the cover which I have linked further down on this page. You can look through them and see how the rails will clamp onto your Titan truck bed.

expert reply by: Robin H

0

Robin H.

1/12/2026

Hey Dave, were you able to review the installation instructions for the BAK Revolver X4s on your Titan with the Utili-Track system? Knowing how the rails clamped onto the bed could help others setting up the same cover. Your feedback might make it easier for the next Titan owner to follow along.

Answer 1

I have a solution for you. First, though, the Rola Haul-Your-Might T3, part #59799, is not compatible with the Truxedo TruXport, part #TX297401. The reason is that the TruXport installs on the top of the bed rails and the T3 won't be able to…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Availability of Pictures or Video Installation of BAK Revolver X4s on 2018 Nissan Titan

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching