Recommended Replacement Short Arm Assembly for a Lippert Awning

Question

Question:

i need a set of solera patio awning arms with motor head and the wall mount 63 inches in length

asked by: Marty D

0

Expert Reply:

Marty, it sounds like you're looking for the Replacement Short Arm Assembly for RV Awnings # LC404523. This is going to replace any Lippert Solera short arm assembly, measures 63" long, and includes the wall-mounted bracket, outer arm, inner arm, and pitch arm.

If you have something else, let me know and I'll see what I can find.

expert reply by: Bryce D

0

Answer 1

Since your Solera arm is 58 inches long that would indicate it's a Solera Edge awning which means for a replacement drive arm you would want the part #LC22ED or for a replacement idler arm part #LC62ED.

view full answer...

Answer 2

I reached out to Lippert who said the Kwikee RV Step Motor and Gearbox #LC33UD is the replacement for the part number 366047 actuator motor. The motor is not available separately.

view full answer...

Answer 3

Hey John, for your Kwikee 28 Series Step with a B style linkage the correct replacement motor would be the part #LC379769. How old is your step setup? Older than 1999?

view full answer...

Answer 4

Hey Todd, yes the Solera 2000 Series and Edge Hardware part #LC65AF does come with two arms and the right hand side does have the drive motor but the wires do not come out of the top of the drive motor so you might email me a picture of what you have…

view full answer...

Answer 5

The Solera 12V Power RV Awning Conversion Kit - Universal - 69" Arms - White #LC434724 will absolutely work with a 20 foot awning like #LCV000231498. The motor is absolutely strong enough for that size awning. The awning and the other components…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Recommended Replacement Short Arm Assembly for a Lippert Awning

Products Featured in This Question

Continue Researching