Is There a Way to Get 9 Foot Carpeted Bunk Board For Boat Trailer

Question

Question:

Im looking for a 9 foot marine carpeted bunk board. I don't see anything on the website.

asked by: Dan J

0

Expert Reply:

Hi Dan,

While there isn't a single 9 foot bunk board we offer, what you can do to get that is combine 4 foot long and 5 foot long bunk boards with the CE Smith Carpeted Bunk Boards for Boat Trailers - 4' Long # CE27810 and 5' Long # CE27820.

expert reply by: Kyle S

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 10

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 11

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 12

A replacement tang-style spindle washer like part #5-101 is intended to be installed behind the castle nut and have its prongs bent down so that they prevent the castle nut from rotating on an E-Z Lube type spindle. The castle nut holds the washer in…

view full answer...

Is There a Way to Get 9 Foot Carpeted Bunk Board For Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching