How To Install 7-Way At Hitch And In The Bed Of A 1997 F250 With No Factory 7-Way Or 4-Flat
Updated 02/03/2026 | Published 07/11/2024 >
Products Featured in This Question
Question:
Hello. I have a 1997 Ford F250 HD. Im needing to put a 7 blade plug at my bumper hitch, as well as one in my bed for gooseneck attachments. I do not have either plugs already on the pickup, I need both. Im willing to splice the harness, I dont necessarily need a plug and play. Do you have a product that would fit this criteria? Thank you for your help.
asked by: Cole S
Expert Reply:
Thanks for reaching out, Cole. I do have a solution for you. Here is a list of the parts you will need to install a 7-way plug at the hitch and in the bed of your 1997 Ford F250 HD:
- Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C55316
- Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers # 5506
- Hopkins Endurance Multi-Tow 4-Way Flat to 7-Way RV Trailer Adapter w/ 4-Way Vehicle End Plug # HM47180
- Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness w/ 7-Pole Connector - 6' Long # HM41158
To summarize, the Curt T-Connector, the Wiring Kit and the Hopkins Endurance Multi-Tow plug will have everything you need to wire the truck with a 4-flat and 7-way at the bumper. The Hopkins Endurance connector uses the standard USCAR connector on the back. You will then take the Hopkins 5th wheel harness and tee this into the USCAR connector to run a 7-way to the bed.
Keep in mind that you will also need an electric trailer brake controller in the cab of your truck, such as the Tekonsha P3 # 90195.
You will find a few install videos and installation instruction links below. You can feel free to reach out to me if you have further questions.
Product Page this Question was Asked From
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Vehicle End Connector
- No Converter
- No Tow Package
- 4 Flat
- Plug and Lead
- Plug-In
- Visible
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Will Cummins Onan EC-AGS+ Work With Lithium Batteries
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Is Drilling Required for a Custom Mount Hitch on a 1985 Chevrolet C/K Series Pickup
- Article: Trailer Wiring Diagrams
- Q&A: Looking For Factory 7 Way Connector For 1997 Ford F250 HD 4TB-14A464-AT
- Q&A: What is the Width of Curt Trailer Hitch # C13902
- Q&A: Distance From Rear Bolt Hole to Receiver Opening on B&W Heavy-Duty Trailer Hitch
- Q&A: Will Curt Trailer Hitch Receiver for 1984 Chevy C/K Series Pickup Work with Brackets Under Frame
- Q&A: 1985 Chevy C10 Trailer Hitch Recommendation for Good Ground Clearance
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: How to Mount a Truck Bed Camper
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: How to Measure for Trailer Hitch Drop
- Article: Brake Controller Installation: Starting from Scratch




Jesse M.
2/3/2026
Hey Cole, how did the wiring setup go on your F250 using the Curt harness and the Hopkins connectors? Your update could make it easier for the next person adding both bumper and bed plugs.