Replacement Arm for a Solera Awning V000315307

Question

Question:

Looking for the long arm for an awning I have the tag info Item: AWN1000 Variant: V000315307

asked by: Jeremy J

0

Expert Reply:

Thanks for the information. I wasn't able to find anything on the AWN1000 number but the other one is a LCI Solera V000315307. The only option we have to replace any portion of the arms is the Solera 12V Electric RV Awning Conversion Kit item # LC434723. Nothing else we have will work or just replace the long arm.

expert reply by: Jerred H

0

Jerrad

7/10/2024

This awning is already an electric unit. Will that matter?

Answer 1

Hey Brian, thanks for reaching out! Your Solera awning runs off of 18V power so you we'll need to get you setup with different arms so the 12V power from your battery works with it. To upgrade your arms to the 12V power you need the Solera Regal…

view full answer...

Answer 2

Based on the pictures you definitely need the awning support arm #LC281154. I can't tell in that other photo if the pin is bent or damaged, or just barely hanging in there. I'm also not sure if your idler head and roller endcap are ok or not…

view full answer...

Answer 3

The Regal Drive Head #LC53TF is a little skinnier and doesn't have a logo while the Plain Drive Head #LC273478 is a little wider and has the LCI logo on it (see attached).

view full answer...

Answer 4

While we don't have a way of knowing what awning you have, I can tell you how to choose the right replacement support arms, so long as your awning is a Solera awning. To do so, all you have to do is measure the length of the wall mount, which…

view full answer...

Answer 5

With the Solera XL Power Awning Roller Assembly #LCV000335015 you could use the Solera 12V Electric RV Awning Conversion Kit #LC434723 for a powered kit that would work really well. We also have this in white with the part #LC434724.

view full answer...

Answer 6

Hey Rob! I'm assuming you have a Solera awning, is that correct? Unfortunately, the bracket is not something that is available separately. I know it isn't ideal but, the only way to replace the bracket is with the Replacement Support Arm…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Arm for a Solera Awning V000315307

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching