Replacement Bearings And Grease Seals For A 2020 Keystone Bullet 248RKS Travel Trailer

Question

Question:

I need a timken bearing kit for a 2020 keystone bullet 248rks I believe they have 3500 lb axles Thia

asked by: Scot

0

Expert Reply:

Hi Scot,

To find the correct bearings and grease seals for your 2020 Keystone Bullet 248RKS Travel Trailer you'll need to either check them to see if the part number is still stamped onto them or measure the spindle with a caliper # PTW80157 at points B, C, and D for the inner diameter and the hub bore hole for the outer diameter. Once we have either the part numbers or measurements I can see which Timken bearings will be a compatible fit.

expert reply by: Kevin C

0

Spindle Measurement Guide
(click to enlarge)

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

Thanks for your question, Steve. Installing the Timbren Rear Suspension Enhancement System #T76FR wouldn’t eliminate the need for a weight distribution system if your setup calls for one, they actually serve two different purposes. A weight…

view full answer...

Replacement Bearings And Grease Seals For A 2020 Keystone Bullet 248RKS Travel Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching