Timbrens or SumoSprings Kit Recommendation for 2023 Ram 1500

Question

Question:

Not sure which to get summo spring ot timbren I have a ram 1500 pulling a Jayco 2016 jay feather with a dry weight of 4220 and hitch weight of 410 . Thanks Ed

asked by: Ed

0

Expert Reply:

Hey Ed, since Timbrens are known to be pretty harsh I would go with the SumoSprings kit part # SSR-307-47 as this will give you a better balance of suspension support and ride quality.

expert reply by: Jameson C

0

Answer 1

Hello Donny, thanks for reaching out. We do offer Timbrens for the 2015 Chevy Silverado 2500, for that I recommend part #TGMRCK25D. These likely will affect the adjustment of your weight distribution system. You will want to install the Timbrens…

view full answer...

Answer 2

Hey Steve! The best system for your 2020 Ram 1500 is the SumoSprings Solo Custom Helper Springs #SSR-307-47. The Timbren SES works when you're towing but when you aren't you get a rough ride. The SumoSprings give you the support you need…

view full answer...

Answer 3

Hey William thanks for stopping in! Personally I'd go with SumoSprings #SSR-610-54 over Timbrens. SumoSprings are a progressive spring which means the initial engagement is much softer compared to Timbrens which ultimately gives you better ride…

view full answer...

Answer 4

Yes, Timbren suspension enhancement can be used along with a weight distribution hitch. However, you would not want to use the #TFRTT1504E. This is a severe service kit that is better suited for something like a slide-in camper or salt spreader. The…

view full answer...

Answer 5

For your 2024 Ram 1500 I would choose the SumoSprings Solo Custom Helper Springs #SSR-307-47 over the Timbren #TDR1500DS. Both will be able to give you the extra support with your towing setup. However, the SumoSprings will be a much better option…

view full answer...

Answer 6

Yes, this is normal. The Timbrens will engage first when you hook up the trailer and the weight distribution hitch will then work with the remaining sag. Just make sure you're not overloading your truck's tongue weight capacity and the weight…

view full answer...

Answer 7

On the new 2019 Ram 1500 the factory brake controller port is located under and behind the heater controls on the dash. I have attached an image that points to this location. You should be able to access the plug by simply reaching behind and…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Timbrens or SumoSprings Kit Recommendation for 2023 Ram 1500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching