Which Torklift Camper Tie Downs Fit 2024 Ford F-350 Long Bed with Factory Hitch

Question

Question:

We have a 2024 F350 dually crew cab 8 ft bed with stock side bed steps Will the front tie downs fit? If so what model # Thank you

asked by: Chip S

0

Expert Reply:

Hey Chip, so we do have a set of Torklift camper tie downs that fit your 2024 Ford F-350 long bed with side steps and a factory hitch with the part number # TL87CR for the front set and part # TLF3008 for the rear set.

expert reply by: Jameson C

0

Answer 1

Hey Clifton, thanks for reaching out! The TorkLift Tie Downs #TL87DR, which is a kit comprised of the F2032 and F3008 parts, will fit your 2025 Ford F-250 as long as you have the 8' bed and the factory hitch installed. If you have something else…

view full answer...

Answer 2

Torklift makes the best frame mounted camper tie downs so for your 2020 Ram 2500 with factory boards, short bed, and a factory hitch you'd want the part numbers #TLD2142 and #TLD3113 and you'd be set. You would also need a set of turnbuckles…

view full answer...

Answer 3

I went out to the warehouse and pulled Curt hitch ball #C40085. I took it out to our install bays and grabbed a socket that would fit. It takes a 1-7/8 inch socket or wrench.

view full answer...

Answer 4

Most of the 2-5/16 inch hitch balls will use either a 1-inch diameter shank or 1-1/4 inch diameter shank. The nut size on a hitch ball with a 1-1/4 inch shank, like the Tow Ready 2-5/16 Inch Hitch Ball, part #19286, will use a 1-7/8 inch socket. A…

view full answer...

Answer 5

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Which Torklift Camper Tie Downs Fit 2024 Ford F-350 Long Bed with Factory Hitch

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching