What 3" Wide, 6' Long Hinge Has a 3/16" Thick Side Plate?

Question

Question:

I was needing to know the thickness of the plate on both sides of the barrel. It looks to be about 1/8”, but was needing to know for sure before I order. I need it to be at least 3/16”

asked by: Tanner B

0

Expert Reply:

The side plates on the 3" Wide Continuous Hinge # MA65VR you found are 0.09" thick which is just under 3/32". We do have a 3" Wide # MA52VR which is 6' Long with a 1/2" pin that has 0.18" thick side plates which is slightly thicker than 3/16" thick.

expert reply by: Bud M

0

Answer 1

Marlboro doesn't have a weight capacity for their hinges but you certainly can cut the 4" Wide Continuous Hinge - 6' Long - 5/8" Pin Diameter - Steel #MA42VR down to length. I just recommend separating the pieces before cutting…

view full answer...

Answer 2

I reached out to Marlboro Manufacturing and they informed me that it is okay to cut their 4" Wide Continuous Hinge - 6' Long #MA42VR in half. The said the hinge pin should not be able to slide out but in the event it does try to slide to…

view full answer...

Answer 3

Hinges like the 6" Wide Continuous Hinge - 6' Long - 1/2" Pin Diameter - Steel #MA52VR do not have weight capacity ratings and it is up to the installer to determine if it will be strong enough. We do have a longer 8 foot long variant,…

view full answer...

Answer 4

The 2x2 inch square axle is likely 3,500 lbs or less capacity. I would need more spindle dimensions or bearing numbers to assist. If you pull a hub and measure at the spindle where the bearings and seal ride using the digital caliper like #PTW80157 I…

view full answer...

Answer 5

Steel hinge #SH300 should work well for a flap on your trailer. You can't get a custom length but if you need 67 inches then #SH300 would be the one to get. You can trim it to the length needed. Between you and me, go with #H300. It is exactly…

view full answer...

Answer 6

The way a trailer ramp door is hinged is going to depend on how the manufacturer decides it needs to be hung so it really could be one long piece or several pieces. The hinge(s) may or may not extend all the way to the edges but most of the ones I…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What 3" Wide, 6' Long Hinge Has a 3/16" Thick Side Plate?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching