Replacement Hitch Head for Curt MV Weight Distribution Systems

Question

Question:

I need to send you a photo of a ball mount to see if you have one available

asked by: George H

0

Expert Reply:

Based on your images it appears you need the Replacement Head for Curt MV Weight Distribution Systems # C17075. It has all the same grease zerk positions, spring clips and the same design. You may be able to find a tag on the spring bars themselves to verify if they are Curt since it doesn't appear you have the tag on the head.

expert reply by: Bud M

0

Damaged Curt MV Weight Distribution Hitch Head
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 10

Hey Chris, in the instructions for the B and W Turnoverball gooseneck hitch part #BW73FR that you referenced it says that the inner brackets are not needed if the truck has the inner brackets for the OEM hitch already welded to the truck frame. In…

view full answer...

Answer 11

Hey Jeff, I checked with Firestone and the only version of the 2025 Toyota Tacoma that the part #F83VV doesn't fit is the 2 wheel drive models. The SR5 can be either 4wd or 2wd so you would need to verify which configuration you have to know if…

view full answer...

Answer 12

Hey Josh! Yes, you can lock the BulletProof Hitches Aluminum Adjustable 2-Ball Mount #BPH97MR to your hitch receiver by using the Locking Kit #BPH34FR. This comes with a lock for the hitch receiver as well as the adjustable part of the platform so…

view full answer...

Replacement Hitch Head for Curt MV Weight Distribution Systems

Product Page this Question was Asked From

Continue Researching