Overall Length of 21,000 lb Demco Trailer Coupler DM16080-95

Question

Question:

I was wondering what the total overall length is on the Demco DM16080-95 coupler would like to replace my surge hydraulic coupler and transition to electric breaks on the boat trailer.

asked by: Wade

0

Expert Reply:

Hi there Wade; I was able to get that measurement for you, and the overall length is 18-3/4 inches of the 21,000 lb Demco coupler you asked about, which is the following part number:

- Demco Channel Tongue Trailer Coupler # DM16080-95

expert reply by: Kyle S

0

Overall Length of Demco Coupler DM16080-95
(click to enlarge)

Answer 1

The only difference in the Demco Channel Tongue Trailer Couplers #DM16080-95 and #DM15931-95 is going to be the bolt pattern. One will have the 5-Bolt hole pattern and the other is going to have 4-Bolt holes. I have included images below showing the…

view full answer...

Answer 2

For a lock to use with the Demco Coupler part #DM16080-95 the part #e98888 would work great. It has the correct span and diameter.

view full answer...

Answer 3

Hey Chris! We don't have the weld-on 21K straight coupler from Demco, but you can still use a bolt-on style like the part #DM16080-95 you were looking at and have that welded to your trailer instead of bolting it in place. We used to have the…

view full answer...

Answer 4

We have the Demco Channel Tongue Trailer Coupler #DM16080-52 for a straight tongue and the Demco 50-Degree A-Frame Trailer Coupler #DM16680-52 for A-Frame. Both are made in the USA, are bolt on and rated for up to 21,000lbs. Both come with the…

view full answer...

Answer 5

Georgia, it sounds like the winch you're currently using may not be rated high enough to support the weight of your ski. That, or the bolt itself is not beefy enough. To make sure this does not happen again, I'd suggest using a winch that is…

view full answer...

Answer 6

The channel of the Demco 21K #DM16080-52 coupler is 3 inches deep. The distance from the center of where the trailer ball would sit to the first 5/8 inch hole is 7 inches, and 12 inches to the second hole. The Titan #T4853100 dimensions are a little…

view full answer...

Answer 7

I did pull the Titan Zinc-Plated Straight-Tongue Coupler - 21,000 lbs #T4853100 and measured from the inside top of the coupler to the center of each of the 5 bolt holes from back to front: 2" 1-1/4" 1" 1" 1-1/4" The hours of…

view full answer...

Answer 8

Thank you for the image. It appears you will need either the Demco Channel Tongue Trailer Coupler #DM13203-95 or #DM16080-95. Both of these couplers have a zinc coating for increased corrosion resistance and fit on a standard 3" wide channel…

view full answer...

Answer 9

The base measures 5-3/4" wide (from side to side) and 7" long for the Fulton High-Performance 2-Speed Trailer Winch - Rope Only - Zinc - 2,600 lbs #F142410. The overall height, from bottom to top of the drum, is 7-1/4", and this is for…

view full answer...

Answer 10

Thanks for the photo, and the distance between the front and rear bolt holes is 5 inches for the Demco Channel Tongue Trailer Coupler - Silver - 2-5/16" Ball - 3" Channel - Bolt On - 21K #DM16080-52. So if you measure the bolt holes on your…

view full answer...

Answer 11

Hey Chad, thanks for reaching out. We do offer several 2-5/16" ball couplers, but nothing as long as what you are looking for. Our longest coupler is the Demco #DM16080-95 which is about 18-3/4" long. A lot of our surge brake couplers are…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Overall Length of 21,000 lb Demco Trailer Coupler DM16080-95

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching