How to Determine Which Generation StepAbove Steps You Have

Question

Question:

How do I know if I have a 1st or 2nd gen Morryde 4 step

asked by: Missy

0

Expert Reply:

To find out which gen steps you have, you will want to look at the legs of your steps and look for a pull pin. If you have a pull pin, then you've got the 1st generation. But, If you have a button that releases the legs for adjustment, then you have the second generation steps.

expert reply by: Bryce D

0

Answer 1

Hey Michael, the 5-1/2 inch height of the Valterra StayPut Tandem Trailer Tire Changing Ramp #VAL68MB that you referenced is the center of the "flat" part where the tire rests when fully on the ramp. So basically at the lowest point in the…

view full answer...

Answer 2

Hey Cindy, the PowerMax Membrane Plus RV Roof Replacement Kit w/ Rolled PVC Membrane #PM78VR is rolled. So it ships on a roll and is not folded.

view full answer...

Answer 3

Hey Mordechai! I can help you find replacement leaf springs and shackles but you will have to get some measurements. For the leaf springs you either need to measure the flat length or get the spring eye to spring eye measurement. Both of these are…

view full answer...

Answer 4

Hello Greg, Thanks for writing in, great question! The MORryde Add-A-Step for 23-1/2" Wide Step Above Treads #MR26MV will fit correctly even if the lower handrail kit is installed. The reason is that the handrail attaches to the side frame of…

view full answer...

Answer 5

For your 2021 Keystone Passport SL Travel Trailer with an entry height of 32" and door width of 24", yes, the correct the MORryde StepAbove RV Steps, #MR98RR is for 23-3/4" to 26-1/4" wide doorways and entry height of…

view full answer...

Answer 6

Hey Cody. As long as you’re mounting to a solid support part of the frame, you’ll be good to install the MORryde Safe-T-Rail #MR54BR on your camper without any issues. Your RV should have a frame around the door to support the door as well as the…

view full answer...

Answer 7

You are right on. The 8" rise/drop on the MORryde StepAbove Fold-Down Steps #MR98RR is the height between the steps. The #MR48RR you were looking at has a 9" rise/drop meaning the distance between the steps is 9". The #MR98RR is…

view full answer...

Answer 8

Great questions. I have solutions for both questions. Lippert does not sell replacement bolts or hardware kits for this application you will be able to source the bolts you need from any local hardware store. As for a replacement options I strongly…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hi Donny; after looking at several videos of the trailer it does appear to have a 6 on 5-1/2 bolt pattern with ST225/75R15 tires. The Goodyear Endurance ST225/75R15 Radial Tire w/ 15" Eagle Aluminum Wheel #GY97QB will be a direct fit.

view full answer...

Answer 12

Hi Collin, welcome back! The most economical replacement is going to be from Advent Air. You will need a complete system since everything moved to R32 refrigerant. If your upgraded thermostat is R32 compatible, or a smart thermostat that got a…

view full answer...

How to Determine Which Generation StepAbove Steps You Have

Product Page this Question was Asked From

Continue Researching