Replacement Actuator for UFP 34034

Question

Question:

I need a replacement actuator p/n 34034 Dice brake single axle 2 in coupler.

asked by: James B

0

Expert Reply:

The correct replacement actuator for your UFP 34034 is the Dexter DX7.5L A-60 part # DX56FR.

expert reply by: Jameson C

0

Answer 1

Hey Ryan, yeah you're right TDE is no longer a thing and unfortunately we don't carry a replacement reverse solenoid for that actuator so at this moment your best bet would be to replace the entire thing with the Dexter DX7.5L A-60 Brake…

view full answer...

Answer 2

Yes, you can weld on the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K item #DX56FR you referenced. You will want to make sure you remove the zinc coating and get down to the bare metal. I have…

view full answer...

Answer 3

I assume you have disc brakes since you mentioned an electric lockout, and we do have an A-60 actuator; the correct one will just depend on if you have a 3" x 5" (most likely) or 3" x 4" straight tongue: - 3" x 5":…

view full answer...

Answer 4

Hey Bruce, you'd want to make sure the tongue of your trailer is 3 inch wide to verify for sure that the Dexter actuator part #DX29FR fits. This is also designed for 2 inch hitch balls and the brake type needs to be disc.

view full answer...

Answer 5

While Dexter does offer a Replacement Inner Member #DX99FR for the Dexter DX7.5L A-60 Brake Actuator #DX29FR, the outer case is only available with the entire actuator. You will need to get a whole new actuator but be sure to save your current inner…

view full answer...

Answer 6

I would just use the stainless steel bolt method you mentioned to lock out the coupler you have. That's going to be the easiest and simplest solution. This is a very common solution for your situation where you are wanting to go from the surge…

view full answer...

Answer 7

That's a really good question, and there is a difference between the 7,500 lb Dexter DX7.5L A-60 actuators for disc brakes; the differences are both in what they fit, as well as their length. - 14" Long & Top-Mounted For 3" Wide…

view full answer...

Answer 8

I took a look at the A-60 Surge Brake Actuator like the Dexter #DX56FR, and to remove the front pin you'll need to remove the locking ring from the front rolling pin on the passenger side, and push it out from the passenger side to the driver…

view full answer...

Answer 9

Hey Eric, there there would be no issue with using the Dexter Surge Actuator part #DX56FR with a trailer that has a single brake axle.

view full answer...

Answer 10

The Replacement Shock Absorber Spring Kit #TK71-758-00 is the correct shock for your UFP Surge Brake Actuator. The picture you included does not specify if it is for a disc or drum brake set, so I have found both for you to choose from. Disc Brake…

view full answer...

Answer 11

Yep, you got it, the bolt hole dimensions are 3" x 2-1/2" for the Dexter DX7.5L A-60 Brake Actuator For Disc Brakes #DX29FR. This fits over a 3" x 4" tongue and the ball to opposite end length you stated does not matter, no.

view full answer...

Answer 12

There is not a rebuild kit so you would need to replace your UFP A-60/A-75 disc brake actuator, with the correct one depending on if you have a 3" x 5" or 3" x 4" straight tongue: - 3" x 5" Straight Tongue: Dexter DX7.5L…

view full answer...

Replacement Actuator for UFP 34034

Product Page this Question was Asked From

Continue Researching