Timken Bearings for Trailer with Inner Diameters 1.06 and 1.375 inch

Question

Question:

I need a timken trailer bearing kit for 1.062inch and 1.375inch diameter axles. The axles step down in size. I need bearings for two axles and brakes and drums 10inch diameter drum for one axle. Cant find quality parts and I dont know part numbers. Is there any way that is enough info?

asked by: Jason M

0

Expert Reply:

For the 1.06 inch diameter Timken bearing you would want the part # TM23VR and for the 1.375 inch you'd want the # TMK73VR.

expert reply by: Jameson C

0

Answer 1

If your 2000 Ford F-250 has a GVWR over 8500 lbs, the Firestone Ride Rite #F2550 would be compatible with your B&W Turnover Ball hitch. Air Lift also offers a fit, part #AL57390 with no limitation on the GVWR of the vehicle. Both kits offer…

view full answer...

Answer 2

Hey Barry, sure do! The seal that comes with the #DX87UR bearing kit is a 1.719" ID and 2.565" OD. We offer this seal individually as part #58846.

view full answer...

Answer 3

For each of your Lippert 3500lb axles you will need the following components. Timken Inner Bearing & Race #TMK73VR Qty 2 Timken Outer Bearing & Race #TMK23VR Qty 2 etrailer Grease Seal #58846 Qty 2 Grease Caps #RG04-040 Qty 1 We do not carry…

view full answer...

Answer 4

Yes, the Timbken bearings part #TMK73VR and #TMK23VR are made in the USA.

view full answer...

Answer 5

Thanks for reaching out, Michael! In the past we've recommended the Grease Seal #168233 as a replacement for the AD2527E because it has a 1.688" ID and a 2.332" OD. To replace your L68149 Timken bearing and seal we have the Timken Kit…

view full answer...

Answer 6

The Replacement Trailer Hub Bearing part #L68149 like most trailer bearings if not all are manufactured overseas. This particular bearing is made by AxleTek. We have been using these trailer bearings for quiet some time and have heard nothing but…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Timken Bearings for Trailer with Inner Diameters 1.06 and 1.375 inch

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching