Does Yates Wobble Roller part # YR440R have a Metal Bushing

Question

Question:

does the yates wobble roller YR44oR Have a metal bushing inside the hole or is it just rubber?

asked by: Rik B

1

Helpful Expert Reply:

The Yates Wobble Roller part # YR440R does not have a metal bushing.

expert reply by: Jameson C

1

Answer 1

We have just what you need. To replace the Yates Ribbed Wobble Roller - Heavy-Duty Rubber - 4-3/8" Diameter - 3/4" Shaft #YR343R-6P with a roller that is non-marking you will need the #YR500YW-6P. Now the #YR500YW-6P will be 5/8"…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Kris, the Dutton Lainson winch part #DL15440 does not come with a strap so you will need to order one with it. The part #DL24250 will work great with this winch as it is correct width, is 25 feet in length, and has a capacity of 3,700 lb WLL and…

view full answer...

Answer 11

Hey Terry! In order to mount the CE Smith Fenders #CE19504-2, normally I recommend #CE26098G-2 or #CES54XR (x 2) depending on your application. Do you know if you need the 90 degree bend to attach to the frame of the trailer, or the straight bracket?…

view full answer...

Answer 12

Hey Steven! The etrailer Rust-Resistant 3-Leaf Double Eye Spring for 4K Trailer Axles - 25-1/4" Long - Dacromet #e93SR will be adequate for your 2020 Gulf Stream Vista Cruiser since the Dexter D40 number correlates to a 4,000 lbs hub and drum…

view full answer...

Does Yates Wobble Roller part # YR440R have a Metal Bushing

Product Page this Question was Asked From

Continue Researching