Will Camco Gas Control Valve Work for Older RVQ 500 Gas Grill

Question

Question:

Will this fit an RVQGrill 500? Original equipment is Outdoors Unlimited Model No. RV 500..

asked by: Rocky M

0

Expert Reply:

The connection to the grill looks to be the same for your original RVQ 500 Grill and the Camco LP Gas Control Valve w/ Quick-Connect # CAM57274 so I have no reason to believe that it won't fit.

The only thing you might have problems with is being able to use the Camco valve with your original cover. The Camco valve has a slightly shorter part that threads into the grill than what you currently have which is why I'm thinking the cover might be a problem.

expert reply by: Jon G

0

Valve on RVQ Grill 500
(click to enlarge)

Answer 1

The threaded portion of the Camco LP Gas Control Valve #CAM57274 is a 3/8 inch pipe thread fitting. This portion is what would connect to the Olympian 550 RV Grill #CAM57305.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Hey David, welcome back! The Seaflo Diaphragm Pump for Boats and RVs item #SE58FR is going to be our best replacement option we have for your Shurflo 4900-0201. The variable flow is based on demand so it would not run as hard with lower water usage…

view full answer...

Answer 12

Hey Gregory, that's really good information. You’ve got a few options, but I wouldn’t jump straight to replacing the leaf springs on a half-ton for that size trailer. Since you’re using a Curt weight distribution hitch, that should be doing most…

view full answer...

Will Camco Gas Control Valve Work for Older RVQ 500 Gas Grill

Continue Researching