Will Dutton Lainson Winch DL14996 Fit Same Mount as Shelby 5352

Question

Question:

Good Morning, Does this model have the same bolt holes as the 5352? Thanks

asked by: Ken S

0

Expert Reply:

Yes, the Dutton Lainson hand winch part # DL14996 that you referenced does have a mounting bolt hole pattern that would work on a mount that a Shelby 5352 fits.

expert reply by: Jameson C

0

Answer 1

Shelby is no longer in business and would not be the same as Fulton; there are no ratchet repair kits available for Shelby so you'll need to replace your winch. Keeping in mind that a boat trailer winch has a boat-size-to-winch capacity that is…

view full answer...

Answer 2

There is a winch I recommend replacing your Shelby 5352 with the best option being the Dutton-Lainson Hand Winch with Automatic Brake #DL14927. This is a 1,500 lb capacity winch (you mentioned 2,500 lbs for capacity, though a higher capacity does not…

view full answer...

Answer 3

Shelby Industries, the company that made Shelby winches, no longer exists. They went out of business in 2016 after 34 years. We no longer have repair parts for their products nor do we have documentation for their winches. But for their winch model…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Will Dutton Lainson Winch DL14996 Fit Same Mount as Shelby 5352

Product Page this Question was Asked From

Continue Researching