Weight Distribution Recommendation for 2022 Jayco 22RB

Question

Question:

What WDB is recommended for a Jayco 2022 20RB Travel Trailer?

asked by: Tim

0

Expert Reply:

I wasn't able to find a 20RB from Jayco but I did find a 2022 Jayco 22RB which has a GVWR of 6,750 lbs so for a weight distribution system the Reese round bar kit part # RE94FR would be a great option that is rated properly.

expert reply by: Jameson C

0

Answer 1

I recommend the Fastway e2 Weight Distribution #FA92-00-0800 for your 2021 Jayco Jay Flight SLX 8 264BH. This hitch system is rated for a trailer tongue weight of 400-800lbs and a total trailer weight up to 8,000lbs. Your Jayco has a dry tongue…

view full answer...

Answer 2

For your 2021 Jayco Jay Flight SLX 267BHS I recommend using the Equal-i-zer Weight Distribution System #EQ37100ET. This hitch offers weight distribution and sway control with no need to remove parts when backing up. You Jayco has 695lbs of tongue…

view full answer...

Answer 3

Did your 2018 GMC Yukon XL come with a factory trailer connector? If not then the port is not present and the brake controller would need to be hardwired into the vehicle's wiring harness. If it did then the port should be located up under the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 12

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Weight Distribution Recommendation for 2022 Jayco 22RB

Continue Researching