Is The Pace Edwards Switchblade A Confirmed Fit For A 2023 Ford F-350 Super Duty - 8' Bed

Question

Question:

Will this fit the 2023 F350 w/ 8foot bed?

asked by: Mark B

0

Expert Reply:

Pace Edwards only has their fitments listed up to 2022 so I recommend reaching out to your local Ford dealership to determine if there were any changes to beds between 2022 and 2023. If not, then the Pace Edwards Switchblade Retractable Hard Tonneau Cover # PE66QJ would be a compatible fit.

expert reply by: Kevin C

0

Answer 1

The Rack-It 1000 Series ladder rack mounts inside the truck bed rails so it won't be compatible with any tonneau covers. For an over-the-cab ladder rack system that fits with the Pace Edwards JackRabbit tonneau cover for your 2023 Ford F-350…

view full answer...

Answer 2

Hey Tomasz; yes you can get replacement clamps for your Pace Edwards SwitchBlade, but they don't make a single clamp available so you'll have to go with the set. If that's okay, the correct part is the following: - Replacement Rail Clamps…

view full answer...

Answer 3

Nickis, it sounds like you're looking for the Replacement Reel/ Spring Assembly for Pace Edwards Tonneau Covers #PE86RB which is going to be the replacement reel/spring assembly and will work for the SwitchBlade, UltraGroove, and JackRabbit…

view full answer...

Answer 4

The replacement rail clamps #PE54CV for your Pace Edwards JackRabbit Retractable Hard Tonneau Cover #PE54UV on your 2010 Ford F-250, is not available separately from the kit. This kit does will work with the: -Bedlocker, -Bedlocker with Explorer…

view full answer...

Answer 5

Since your kayaks are pretty long and you'll be towing a fifth wheel trailer the best option will be a single bar roof rack with an upright hitch mounted T-bar mounted in a front hitch on your 2016 Ford F-350. So for that you'd need the…

view full answer...

Answer 6

We have a similar Pace Edwards retractable tonneau cover that can retract at 12 inch increments but the Switchblade part #PE66QJ can only be either all the way open or all the way closed. Instead you'd want the Full Metal Jacket part #PE89QJ…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Hey David, it sounds like you know what you're doing but I've also gone ahead and found the wiring diagram for the Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR for you to check out so you can use it as a cross…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi Jim! As long as your 2026 Alliance Valor 37V11 has the Lippert Rhino box currently, the B&W 5th Wheel to Gooseneck Pin Box - Lippert Rhino - 25K GTW - 3.25K TW #BW23RV will indeed fit. If you have a different pin box, just let me know and I…

view full answer...

Is The Pace Edwards Switchblade A Confirmed Fit For A 2023 Ford F-350 Super Duty - 8' Bed

Product Page this Question was Asked From

Continue Researching