Adapter for Rhino Rack Batwing to fit HD Rhino Rack Crossbars

Question

Question:

I know it’s possible to mount an awning on the HD crossbars directly. I already have an awning and a spare tent/room that connects to it. I just need to know what bracket I would need to have to make it all work. Thank you

asked by: Benjamin S

0

Expert Reply:

The adapter part number you need for the Rhino Rack Batwing part # RR33100 to fit HD crossbars would be the part # RR31102.

expert reply by: Jameson C

0

Answer 1

Here are the 2 different mounting options for installing the Batwing and Foxwing Awning Relocation Kit #RR31102. You can change the orientation of the brackets so that the awning will either hang higher or lower depending on your application.

view full answer...

Answer 2

The dimension you are looking for on the #RR31102 is 1-1/2".

view full answer...

Answer 3

The Rhino Rack Batwing Awning part #RR33100 that you referenced will fit and work great on Rhino Rack HD bars but you'll need to use the HD bar adapter part #RR31102 and you'll be set.

view full answer...

Answer 4

I measured the spacing between the holes on the top and bottom of the Batwing and Foxwing Awning Relocation Kit for Rhino-Rack Heavy-Duty Crossbars #RR31102 for you and as you can see by the accompanying diagram, the distance between the top…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Roy, welcome back! The mounting hardware available for the Batwing Awnings attaches to crossbars or platform racks. I don't have a way to attach a Batwing awning directly to the side or top of your Popup camper and Rhino-Rack doesn't…

view full answer...

Answer 8

We have some awnings that can mount to crossbars and wraparound the back of the vehicle, like the Rhino-Rack Batwing Awning #RR33100, but none of the awnings that I have seen will attached to the smaller bars that you have on the Thule Canyon XT…

view full answer...

Answer 9

The Thule Interstate Rooftop Cargo Bag #TH869 that you referenced does not need to fit totally between the crossbars of a roof rack. If you check out the picture I attached you'll see that it can attach to a roof rack and set on top of the bars…

view full answer...

Answer 10

I apologize for any confusion on what the proper torque specs are for 1/2 inch lug nuts on trailer wheels. I attached a picture of a chart to the right that details what the proper torque specs are for a trailer wheels lugs based on lug size, wheel…

view full answer...

Answer 11

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 12

You will be able to mount the Rhino-Rack Batwing awning #RR33100 (driver's side mount) or #RR33200 (passenger side mount)on the FrontRunner Slimline 2 roof rack using the included hardware in the T-slots on your rack. This mounts in the same…

view full answer...

Adapter for Rhino Rack Batwing to fit HD Rhino Rack Crossbars

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching