What Size Hole Saw Is Needed To Install the SmartPlug RV Power Inlet and Connector?
Updated 03/23/2024 | Published 02/27/2023
Products Featured in This Question
Question:
What size holesaw do you use. To make your cut in wall of trailer or boat.
asked by: Dana
0
Expert Reply:
Since the SmartPlug RV Power Inlet and Connector - 30 Amp # SM77FR is 3" wide, you could use the 3" hole saw like what's in the kit # PT34VR and then use a sanding tool to sand the hole until you get a snug fit.
You'll just want to make sure the hole you make is not larger than 3-1/4" as then the receptacle that houses the plug would have nothing to bite into.
Attached is a dimensional diagram for your reference.
expert reply by:
Bryce D
0
SmartPlug Dimensions
(click to enlarge)
(click to enlarge)
Overall Dimensions
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
SmartPlug RV Power Inlet and Connector - 30 Amp - White
- RV Power Inlets
- Power Inlets
- 30 Amp
- Plastic
- Standard Connector
- White
- SmartPlug
more information >
Continue Researching
- Shop: SmartPlug RV Power Inlet and Connector - 30 Amp - Black
- Shop: SmartPlug RV and Marine Power Inlet and Connector - 50 Amp - Stainless Steel
- Video: Checking Out the SmartPlug RV/Marine Data Port Inlet
- Search Results: smartplug ethernet
- Shop: VanTred Custom Floor Mat for Cargo Vans - Black - Thermoplastic
- Shop: SmartPlug RV/Marine Data Port Inlet - Blank and Open Port - Black
- Shop: Keystone Single Jack Ethernet Connector for SmartPlug Data Port Inlet - Qty 1
- Shop: SmartPlug RV Power Inlet and Connector - 30 Amp - White
- Shop: SmartPlug RV Power Inlet - 30 Amp - Black
- Search Results: floor
- Search Results: floor liner floor mats
- Video: Review of the Hughes Autoformers Safe View Smart Power Inlet
- Video: Ultimate Overview of the MaxxFan Mini Plus Manual RV Roof Vent w/ 12V Fan
- Video: All About the MaxxFan Dome Plus Roof Vent w/ 12V Fan
- Video: The Low-Down on the SmartPlug RV Power Inlet
- Video: Feature Breakdown: Kat's Heaters Custom Engine Block Heater-KH11483
- Search Results: rv power
- Video: Review of Progressive Dynamics RV Converters - Smart System Included - PD4060K
- Q&A: How to Use SmartPlug System for Starlink Entry Port
- Search Results: roof racks
- Search Results: roof rack
- Q&A: Is There a Replacement for a Trimark 030-0900 Door Latch
- Q&A: Upgrade/Replacement 30 Amp RV Power Inlet and Connector to the SmartPlug
- Search Results: maxxair rv vents and fans
- Q&A: What Are the Dimensions of the 30 Amp SmartPlug RV Power Inlet and Connector
- Q&A: Recommended Replacement Struts for Storage Compartments
- Q&A: What Info is Needed to Pick Out Replacement Gas Shock for Camper
- Q&A: How To Choose the Correct JR Products Gas Shock
- Shop: Vehicle Engine Heaters
Mark J.
3/23/2024
The SmartPlug BF30 dimensions document and installation template shows a 2.43" diameter hole as the minimum hole size required to install the inlet. A 2.5" hole is adequate, and a 2.625" (2 5/8") is on the large side. Cutting a 3" hole in the trailer/vehicle/RV to install the SmartPlug 30 amp inlet leaves very little overlap between the gasket and the skin around the hole.