Recommended RV Toilet For A 9" Mounting Bolt To Wall Clearance Measurement

Question

Question:

I have a Thetford toilet I eill be replacing, hopefully with a Dometic 320 elongated bowl toilet. My floor bolts are. Just over 9 from the wall behind the toilet. Will that be enough room? TY

asked by: De

0

Expert Reply:

The Dometic 320 Full-Timer RV Toilet # DOM27FR requires 11" of clearance from the mounting bolts to the wall for it to fit. We do carry the Dometic 300 Weekender RV Toilet which comes in White # DOM64FR and Tan # DOM74FR and only requires 8.5" of clearance.

expert reply by: Kevin C

0

Answer 1

The main difference between the Dometic 310 Part-Timer RV Toilet #DOM57FR and the Dometic 311 Part-Timer RV Toilet #DOM67FR is that the 310 is standard height (20" tall) and the 311 is a low profile (15-1/2" tall). Both toilets will mount…

view full answer...

Answer 2

The only toilet model we have that fits with a 9-1/2" wall to center of flange measurement is the Dometic 300 Weekender RV Toilet which comes in White #DOM64FR and Tan #DOM74FR. The rest of our options, including the Full-Timer, require a…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 5

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

First you will need to replace your factory hitch on your 2024 Ford F-350 with the TorkLift SuperHitch Magnum Trailer Hitch Receiver #TL27CR. Then you will be able to attach the Rear Tie-Downs #TLR3504 to their receiver. For the front we have the…

view full answer...

Answer 9

Hi Clint, welcome back The HappiJac Original Turnbuckles for Camper Tie-Downs - Stainless Steel - Qty 4 #LC182898 are likely what you are looking for and will be a good in between option (they are actually pretty nice and should last a good long…

view full answer...

Answer 10

Hi Lance, I completely understand where you’re coming from on this. You can use your factory hitch with a 48 inch extension like part #TLE1648, so you don’t have to jump to the dual receiver setup right away since this extension is designed to work…

view full answer...

Answer 11

Hello Dennis, That is definitely something you will want to check with your setup. The B&W Continuum #BW78FR will sit about 9 inches below your trailer frame once installed, so you will want to measure from the ground to the bottom of the frame…

view full answer...

Answer 12

Hey Jack, yes the Torklift camper tie downs part #TL63PR are the correct set for your 2024 Ford F-350 Tremor with a short bed and factory hitch. The turnbuckles part #TLS9526-2 that you referenced as well would be a great set that matches what you…

view full answer...

Recommended RV Toilet For A 9" Mounting Bolt To Wall Clearance Measurement

Continue Researching