What Size Socket Is Needed With the Replacement Hardware Kit for Blue-Ox 2-Point WDH?

Question

Question:

What size of socket do I need to adjust the height of my BlueOx hitch?

asked by: Tim M

0

Expert Reply:

The two 3/4”-10 x 4-1/2” Hex Head Bolts in the Replacement Hardware Kit for Blue Ox 2-Point Weight Distribution Hitch # BLU58XR will need a 1-1/8" socket and will need to be torqued to 250-ft.-lbs.

Attached is a product overview video for you to check out as well.

expert reply by: Bryce D

0

Answer 1

I have a solution for the gooseneck hitch cover, but the two outer holes would only be available through Nissan. You can use the Curt #C66165 for the gooseneck hitch cover on your 2016 Nissan Titan XD, which will give your gooseneck hitch protection…

view full answer...

Answer 2

Hello Patrick. I did a little research after you mentioned drilling, and I see that the 1976 Airstream Sovereign used torsion axles. We unfortunately do not carry torsion axles. I do however have a different kind of axle for you to consider, the…

view full answer...

Answer 3

I would recommend that Blue Ox TrackPro #BLU77FR simply because it does not have lift chains like the SwayPro #BXW1006. Both will do a great job but the TrackPro will have a little less movement because of the absence of drop chains. Blue Ox is a…

view full answer...

Answer 4

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 5

Hey Mike, it is important that you use the included power cable with the Furrion Vision S+ Wireless RV Backup System w/ 1 Camera #FR57AD like the instructions indicate. If this is like a hardwire install I would look for a cigarette lighter to 2-wire…

view full answer...

Answer 6

So if the top of your receiver is 24 inches and the bottom of your coupler is 20 inches then you are correct, you do need a 4 inch drop. To get this, you will need to use the Fastway e2 Weight Distribution Shank - 12" Long - 10-1/4" Rise,…

view full answer...

Answer 7

Your weight distribution system uses a Shank #FA92-02-4100 that gives you a maximum 6-1/4" of rise and 2-1/4" of drop. I recommend using the Fastway Shank #FA92-02-4214. This will give you up to 10" of rise and 7-1/4" of drop with…

view full answer...

Answer 8

Hello Ryan. Your Dexter 5,100 lb axle uses the #25580 inner bearing and a #LM67048 outer bearing. For a bearing kit, part #BK3-300 is what you need. The brake assemblies will essentially be the same as the standard 5.2K-7K brakes with the 12x2 brake…

view full answer...

Answer 9

The Blue Ox #BX88177 consists of two 1/2 inch diameter and 2 5/8 inch diameter pins. They are only able to have the 4 keyed alike. The measurement is 4-3/8 inches between the opening like #BX88212 which cannot be keyed alike . The only option to get…

view full answer...

Answer 10

The locking pins are built into the head on the old style systems so if this is what you have you'll need a new head which we do offer as the Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011.

view full answer...

What Size Socket Is Needed With the Replacement Hardware Kit for Blue-Ox 2-Point WDH?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching