In-Bed Tie-Down Recommendations for a 2023 GMC Sierra 2500

Question

Question:

I have a 2023 Sierra 2500 and I want to install some clean looking tie-down points in my truck bed. Do you have anything that looks better than the factory rings that are already there?

asked by: Sergio

0

Expert Reply:

Thanks for reaching out!

We do have some clean looking tie-down anchors you can install in the bed of your 2023 GMC Sierra 2500; the BullRing Retractable Tie-Down Anchors which come in a 4-Pack # BU23FR or 9-Pack # BU83FR depending on what you're wanting.

These are pretty straightforward to install and they are very easy to use. I've attached a review video for you to check out that goes over the features and the installation!

expert reply by: Jon G

0

Answer 1

Hi JT, Each BullRing Truck Bed Side Wall Anchor #BU83FR has a 1,000lb capacity. That being said the bed wall would likely not have that same capacity so you'd need to check with Chevy/GM to determine what that capacity is. If you have any other…

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Hi Richard! From the top of the shank to the lowest part where the tri-ball sits on the #BWTS20067BMP is 11.125". If you have the balls at max drop with the tallest one hanging down that would be 12.5". We recommend at least 11" of…

view full answer...

Answer 6

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 7

Yes, there is Rob. To replace your Rhino box with a Gen-Y Nomad Gooseneck Pin Box you'll need item #GY37ND. From the top mounting holes to where the gooseneck ball connects is 20.32". The front mounting bolts are 13.45" back and the…

view full answer...

Answer 8

Linda, the Nomad’s coupler is an auto-latching 2-5/16 inch gooseneck, and it’s designed to grab the ball the moment the weight settles onto it. Slight unevenness doesn’t hurt anything - as long as the ball enters the throat of the coupler, the latch…

view full answer...

Answer 9

Hi Curtis! We have you covered! Pun intended. ^___^ What you are looking for are the following parts: Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover w Explorer Rails - Aluminum #PE36CV Pace Edwards Contractor Rig Rack Truck Bed…

view full answer...

Answer 10

All the MORryde Cushioned 5th Wheel Pin Boxes #MR57VR, #MR37VR and #MR97VR will share the same dimensions and are nearly identical to the Lippert 1716 5th Wheel Pin Box #LC1324791. I have attached a technical drawing for the MORryde pin boxes similar…

view full answer...

Answer 11

The towing capacity of the 2003 Chevrolet Avalanche 1500 with 5.3L V8 and 4.10 rear axle is 8100-lbs. For a 7600-lb GVWR travel trailer the resulting 500-lb safety margin is adequate/low-ish. With a trailer that weighs substantially more than the tow…

view full answer...

In-Bed Tie-Down Recommendations for a 2023 GMC Sierra 2500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching