Replacement Hinge Seal for an Extang Solid Fold Tonneau Cover On A 2013 Chevrolet Silverado

Question

Question:

Looking for Hinge Seal to replace all four rubber seal strips for an Extang Solid Fold Model 56650 installed on a 2013 Silverado Extended Cab 6.5 bed in 2013. thanks

asked by: Joel H

0

Expert Reply:

The correct replacement hinge seal for your Extang Solid Fold tonneau cover 56650 is the:

-Replacement Hinge Seal for Extang Solid Fold 2.0 Tonneau Covers # EX32560669.

expert reply by: Bryce D

0

Answer 1

Replacement Hinge Seal #EX32560669 is sold in quantities of 1. It is 69 inches long and was designed as a replacement for Extang Solid Fold 2.0 Tonneau covers. But it would likely fit (but hasn't been tested) with other, similar covers. The only…

view full answer...

Answer 2

Hey Charles. The Replacement Hinge Seal for Extang Encore Tonneau Covers item #EX32620464 is only going to replace one of your 4 seals. It measures 64-1/2" long. What kind of truck do you have?

view full answer...

Answer 3

Thanks for reaching out, Marion! The Replacement Hinge Seal #EX32620464 includes 1 seal that measures 64-1/2" long so if you need to replace 4 of yours, then you'll need to order 4 of these. You'll trim any excess of the seal once you…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Since your 2016 GMC Sierra 1500 already has a 7-way trailer connector at the rear of the vehicle then all you will need to install a brake controller is the brake controller and wiring harness adapter. I am not sure what the "work model" of…

view full answer...

Answer 6

Hey Dave! We have three different types of replacement seals for the Extang Solid Fold 2.0 Tonneau Covers. I have listed them below: Replacement Side Seal for Extang Solid Fold 2.0 Tonneau Covers item #EX32560368 Replacement Cab Seal for Extang Solid…

view full answer...

Answer 7

Thanks for reaching out, Russell! You should be able to slide the old seal out and then the Replacement Hinge Seal for Extang Solid Fold 2.0 Tonneau Covers #EX32560669 should just slide right in place of it. If you can shoot me some photos of what…

view full answer...

Answer 8

If you have the Extang Solid Fold 2.0 Hard Tonneau Cover then you will first need to remove the tail hinge end caps on each side of the panel. Once these are removed you will see that there is a channel on the hinge and a groove on the cover that…

view full answer...

Answer 9

The hinge seal you've looked at, part #EX32560669 would indeed be the correct hinge seal for your older Extang tonneau cover. Just to be sure, I called Extang and confirmed the fit with my representative.

view full answer...

Answer 10

We do have a wiring diagram for you! Whether you have the 1,000 psi Dexter DX Series #K71-650 or the 1,600 psi Dexter DX Series #K71-651 the wiring will be the exact same. I have attached a wiring diagram and review videos for you to check out. Just…

view full answer...

Answer 11

Hey, Wayne. After some checking, It looks like the hinge seal for the Encore cover were recently discontinued and are no longer available for us to get directly from Extang. Sometimes they will keep some stock for themselves to last a bit longer so…

view full answer...

Replacement Hinge Seal for an Extang Solid Fold Tonneau Cover On A 2013 Chevrolet Silverado

Product Page this Question was Asked From

Continue Researching