Size of Allen Wrench Needed to Replace Lock Cylinder in Diversi-Tech Aluminum Ball Mounts

Question

Question:

What size allen key is needed to replace the lock cylinder

asked by: Joseph

0

Expert Reply:

According to my buddy at Diversi-Tech, the set screw that holds the lock cylinder in uses a .050 inch Allen wrench. Before attempting to remove the screw, I would highly recommend soaking the set screw with some penetrating oil because the set screw will have a bit of thread locker on it.

The # DTLBM02RK re-key kit includes the Allen wrench.

expert reply by: Mike L

0

Answer 1

Since you do not know the key number for your Self-Locking, Adjustable 2-Ball Mount, Stainless Balls - 2.5" Hitch - 6" Drop/7" Rise #DTALBM6625-2S and currently have the hitch installed on your truck, you will need the Re-Keying Kit…

view full answer...

Answer 2

The set screw that holds the locks such as #DTLBM02RK to the ball mount is a 0.05 inch so you would need a 0.05 Allen wrench. But if it is stripped at the screw too you may need to just try numerous sizes to find one that fits the best. That is…

view full answer...

Answer 3

There is a re-keying kit we offer for the ball mount part #DTALBM6625 it is part #DTLBM02RK. It comes with new lock cores and a wrench that allows you to remove the lock cores. I attached an install video for the kit that will walk you through the…

view full answer...

Answer 4

GM refers to that circuit as the 'Trailer parking lamp'. The fuse is in location #41 in the fuse box in the engine compartment. After replacing the fuse, you'll want to closely examine the running lamp circuit on your trailer. You'll…

view full answer...

Answer 5

There are adapters which will attach to the D-ring bumper mounts on your 2020 Jeep Gladiator with an ARB bumper, though I was unable to find the exact size of the D-rings of your bumper. I recommend the Roadmaster option, and you simply need to take…

view full answer...

Answer 6

Malone doesn't make that particular anti-rattle device in a size for a 2-1/2 inch receiver, but might have a thing or two that could work for you. Take a look at the Gen-Y Anti-Rattle Clamp, part #325-GH-063. The wedge portion is 1 inch long as…

view full answer...

Answer 7

Yes, the Brake Buddy Select 3 Portable Supplemental Braking System #HM39524 will fit your 2021 Jeep Gladiator. I recommend this as the best portable system for you. The inclusion of the charge line is definitely nice to have included, and the fold…

view full answer...

Answer 8

The anti-rattle adapter I recommend is the No-Rattle Trailer Hitch Wedge, part #MPG908. This will work for 1-1/4 inch and 2 inch receivers and is designed to insert into the small gap that may exist on your receiver. You then tighten it up after it…

view full answer...

Answer 9

When you have all 4 wheels of the toad on the ground, the tongue weight is next to nothing. The 200 pound rating does account for sudden but brief increases in tongue weight such as bumps in the road. The idea of using a high-low adapter like #RM-070…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

There are a number of parts needed in order to flat tow your 2019 Jeep Wrangler JK with a standard factory bumper; I will list the parts for you below. - Base Plate Kit: Roadmaster EZ5 Base Plate Kit #RM-521453-5 - Tow Bar: Roadmaster Falcon All…

view full answer...

Answer 12

On GM vehicles of that vintage, the 12-V pin should be hot regardless of whether the ignition is on or not. If it isn't showing voltage even with the ignition on, you're almost certainly on the right track thinking it's a blown or…

view full answer...

Size of Allen Wrench Needed to Replace Lock Cylinder in Diversi-Tech Aluminum Ball Mounts

Product Page this Question was Asked From

Continue Researching