Dimensions of MORryde X-Factor Crossmember End Plates

Question

Question:

Can you tell me the dimensions of the end plates on this crossmember?

asked by: Jeff M

1

Helpful Expert Reply:

The end plates on the MORryde X-Factor Crossmember for LRE, RE, or TRE Leaf Spring Suspension # MR99ZR measure 4" x 8". The mounting holes line up with the LRE, RE, and TRE brackets. See the dimensional drawing below.

expert reply by: Robin H

1

MR99ZR Dimensions.
(click to enlarge)

Answer 1

Well you've reached out to the right place, Kaivon - I'd be happy to help you navigate upgrading your trailer suspension! All three of those suspension kits you asked about are great, but my recommendation is using the MORryde Rubber…

view full answer...

Answer 2

Hey Rick, the distance between the vertical bolt holes of the mounting flange of the MORryde X-Factor part #MR99ZR is 6-1/2 inches and from side to side is 3 inches.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 6

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 7

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 8

Hi Chas, The Lippert Road Armor Shock Absorbing Equalizer part #LC53CK may work for your trailer, but that will depend on what equalizer is currently on your trailer. In order to determine what equalizers would be a fit for your trailer, we'll…

view full answer...

Answer 9

Hey Eric. Axle spacing isn't the best way to determine what replacement equalizers you need. The most accurate way to find a replacement is to match up a replacing equalizer as close as possible to the dimensions of the one currently on your…

view full answer...

Answer 10

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 11

Hi Rob, The Taskmaster Trailer Wheel Lug Nut part #TA66QR requires a 3/4" socket for installation. However, we do have the CE Smith Trailer Wheel Acorn Lug Nut part #CE16720 that is 1/2"-20 with a chrome plate finish and works with a…

view full answer...

Answer 12

Hello Lanny, thanks for reaching out. The CRE 3000 is already a pretty good suspension system, but if you want to upgrade, the first thing that comes to mind are the AllTrek 4000 equalizers. They have more rubber than the CRE 3000, 40% more, so you…

view full answer...

Dimensions of MORryde X-Factor Crossmember End Plates

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching