Quantity Included On The 3-Leaf Slipper Spring with Radius End # e99SR

Question

Question:

Is this price for a pair of springs or a single?

asked by: Bob

0

Expert Reply:

The 3-Leaf Slipper Spring w/ Radius End # e99SR comes with one single spring. You will have to purchase two to complete the axle.

This spring has a measurement of 24-5/8 inches from center of spring eye to center of spring eye. The spring is for a 1,500 pound axle capacity. It has a sturdy steel construction and the nylon bushings are included.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 3

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 4

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 5

There is no exact way to determine the leaf spring length. The best way to determine the length for a replacement is by measuring the existing leaf springs. The hanger distance and shackle length can help you get a good idea, but you're looking…

view full answer...

Answer 6

Hi Chas, The Lippert Road Armor Shock Absorbing Equalizer part #LC53CK may work for your trailer, but that will depend on what equalizer is currently on your trailer. In order to determine what equalizers would be a fit for your trailer, we'll…

view full answer...

Answer 7

Hey, Lance. The direction the springs are in doesn't matter. They can be to the front or to the rear of the axle and will perform the same either way. What kind of trailer are you working on?

view full answer...

Answer 8

Hey Eric. Axle spacing isn't the best way to determine what replacement equalizers you need. The most accurate way to find a replacement is to match up a replacing equalizer as close as possible to the dimensions of the one currently on your…

view full answer...

Answer 9

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 10

As long as the weight capacity is inline with your trailer/axle rating and the measurements match your current springs, the number of leaves in a spring pack does not matter. The difference between a 3 and 4 leaf spring pack within the same weight…

view full answer...

Answer 11

Hey Jason, it's pretty common for replacement leaf springs to be slightly shorter than what they replace as springs tend to stretch/flatten overtime as they wear out so while you are on the right track 3/4 of an inch is a bit too much of a…

view full answer...

Answer 12

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Quantity Included On The 3-Leaf Slipper Spring with Radius End # e99SR

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching