Trailer Bearings Needed For The Timbren Axle-Less Trailer Suspension System
Updated 09/08/2022 | Published 09/07/2022
Products Featured in This Question
Question:
Im looking at purchasing this axle system for my trailer. My current hubs are 5 x 4.5. I would like to use these but Im not sure of how to find bearing and spindle specs to compare. I basically would like to figure out if my current hubs will fit on the Timbrens and what would be required..
asked by: Julie B
Helpful Expert Reply:
The Timbren Axle-Less Trailer Suspension System # ASR1200S02 use the same inner and outer bearing # L44649. If your bearings match your hub is good to go. If your bearings do not match you will need The Easy Grease Trailer Hub and Drum Assembly # AKHD-545-2-EZ-2K.
This hub assembly has a bolt pattern of 5 on 4-1/2 inches and has a 1/2 inch diameter x 1-1/4 inch long wheel stud. This hub is pre-greased and comes with the bearings, races, grease seal, grease cap, and lug nuts. This hub has an inner/outer bearing # L44649 and will work with the Timbren Axle-Less Suspension System mentioned above.
I attached a review video link below.
Product Page this Question was Asked From
Timbren Axle-Less Trailer Suspension - Standard Duty - No Drop - 1,200 lbs
- Trailer Axles
- Rubber Spring Suspension
- Standard Grade
- No Hubs
- 1200 lbs
- Spindles Only
- Universal Fit
- No Drop or Lift
- Timbren
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: Trailer Idler Hub Assembly for 2,500-lb Axles: The Breakdown
- Shop: Timbren Axle-Less Trailer Suspension - Heavy Duty - Long Spindle w/ 4" Lift - 4 Bolt - 2K
- Shop: Timbren Axle-Less Trailer Suspension - Standard Duty - No Drop - 1,200 lbs
- Shop: Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2 - Qty 2
- Shop: Easy Grease Trailer Idler Hub for 2K Axles - 13" to 15" Wheels - 5 on 4-1/2 - Pre-Greased
- Search Results: c jack
- Search Results: stabilizer jacks camper jacks
- Search Results: akihub~545~2~2k
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Timbren Axle-Less Trailer Suspension - Heavy Duty - Long Spindle w/ 4" Lift - 4 Bolt - 2.2K
- Shop: Timbren Axle-Less Trailer Suspension - Heavy Duty - 4" Lift - 4 Bolt Flange - 2,200 lbs
- Search Results: timbren trailer hubs and drums
- Q&A: Does Timbren Axle Less System A20RS545 have Rim Diameter Restrictions
- Q&A: Do Pre-Greased Trailer Hubs Require Any Greasing Prior to Install
- Q&A: Will the 2K Timbren Axle-Less System A20RS545 Work with 15 Inch wheels
- Q&A: Recommended Hub and 14-15 Inch Wheel and Tire for Timbren Axle-Less Trailer Suspension
- Q&A: Timbren Axle-Less System vs. Torsion Axles for a Sail Boat Trailer
- Q&A: Is the Capacity of the Timbren Axle-Less Suspension System the Total Capacity?
- Q&A: Difference Between Hubs Designed For 8-10 Wheels and Hubs Designed For 13-15 Wheels