Is Pre-Greased Easy Grease Trailer Hub Compatible with LMX Red Grease

Question

Question:

Is the grease in the pre-greased brake drum/hub #AKHD 865-7-EZ-K compatible with LubriMatic LMX RED Grease? Thank you,

asked by: Daniel B

0

Expert Reply:

Yes, the grease that is in the Easy Grease Trailer Hub and Drum Assembly # AKHD-865-7-1-EZ-K is compatible with LMX Red grease like the part # L11390 as it is Lithium Complex grease which is the same as the LMX Red grease.

expert reply by: Jameson C

0

Answer 1

The difference between Dexter Nev-R-Adjust Electric Trailer Brake Assembly - Right Hand #23-465 with Left Hand #23-464 and the Dexter Electric Trailer Brake Kit - Left and Right Hand Assemblies #23-180-181 is that the former is self-adjusting while…

view full answer...

Answer 2

The seal needed is going to depend on the inner and outer bearing numbers stamped into the sides of the bearings. Or if you know the part number of the hub I could look it up to determine the correct seal. The grease seal though is meant to hold the…

view full answer...

Answer 3

The left side is the driver side, right side is passenger side. On a trailer brake assembly like #23-105 the arm that the magnet is on points to the front of the trailer and the magnet always will be on the bottom. I have included a picture that…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Is Pre-Greased Easy Grease Trailer Hub Compatible with LMX Red Grease

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching