How Does Grease Reach The Bearings On The CE Smith Trailer Axle Beam # CE33201GA?

Question

Question:

Does the grease reach the back bearings when using grease gun or is hub removal necessary for greasing? I didnt see a hole near the base of the spindle, only near the end.

asked by: Tom F

0

Expert Reply:

Yes, the grease will reach the inner bearing through a hole on the spindle on the CE Smith Trailer Axle Beam # CE33201GA. I have included an image below that shows the hole in the spindle.

expert reply by: Bud M

0

EZ Lube Grease Hole on CE Smith Trailer Axle Beam # CE33201GA
(click to enlarge)

Answer 1

Yes, the Easy Grease Trailer Idler Hub Assembly #AKIHUB-545-2-EZ-2K will fit the CE Smith Trailer Axle Beam with EZ-Lube Standard Spindles #CE33201GA. The EZ grease caps that come with the hub assembly will work with the EZ grease spindle on the…

view full answer...

Answer 2

The first step in order to replace the axle on your Right on Trailer Multi Sport Trailer is to take a few measurements, the spring center and hub face (see photo). Once we have these we can get you setup with one that will allow you to use your…

view full answer...

Answer 3

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 4

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

How Does Grease Reach The Bearings On The CE Smith Trailer Axle Beam # CE33201GA?

Product Page this Question was Asked From

Continue Researching