Best Way to Attach Thule Hullavator to Rhino Rack Pioneer Platform Roof Tray

Question

Question:

What is the best way to attach the Thule Hullavator to the Rhino Pioneer Platform?

asked by: Dean

0

Expert Reply:

The Thule Hullavator part # TH898 has ability to attach to top channels of crossbars like what the Rhino Rack Pioneer Platforms like # RR59AB have so you could attach the Hullavator to the top of the platform using the included T-bolt hardware no problem.

expert reply by: Jameson C

0

Answer 1

In order to use the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs part #TH898 on a 2017 Jeep Wrangler Hard Top you will need a roof rack which has standard crossbars that overhang past the mounting feet at least 4". The Thule…

view full answer...

Answer 2

The Thule Hullavator Pro Kayak Roof Rack #TH898 will either clamp around the Thule WingBar Evo Crossbars #TH711420 or can be held inside the channel. The Bar Mount Assembly #7521741001 included with the carrier allows for either style attachment to…

view full answer...

Answer 3

Hey Geraldine, yes the Thule Hullavator part #TH898 can install on a Rhino Rack ROC25 roof rack as it can either attach directly to the top channel of the crossbar or use the other set of hardware that can wrap around it. The Hullavator does need 4…

view full answer...

Answer 4

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Answer 5

The Thule Hullavator #TH898 comes with hardware needed to attach to Rhino Rack crossbars. They can wrap around the bars or if they are the aero or HD bars the T-bolt attachment can be used instead.

view full answer...

Answer 6

Both the current Hullavator Pro #TH898 and the older model, part 897XT that you have, require the crossbars to overhang the feet of the roof rack by 4" - 8" for their to be enough clearance to lower the carrier without making contact with…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hello Travis, Thanks for writing in! Your father-in-law's Demco Autoslide 5th Wheel Trailer Hitch for Dodge Ram - Single Jaw - Above Bed - 18,000 lbs #DM59XV is built to mount to industry-standard above-bed rails, so it won't drop right into…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Best Way to Attach Thule Hullavator to Rhino Rack Pioneer Platform Roof Tray

Products Featured in This Question

Continue Researching