Grease Seal w/ Inner Diameter of 1.687" and an Outer Diameter of 2.561"

Question

Question:

Having a hard time finding the right grease seal for a 2007 Tracker Trailstar trailer. The spindle/ID is 1.69 and the OD is 2.56. The spindle looks like an EZ grease, maybe by Dexter/UFP. Do you have something for this model?

asked by: Matt

0

Expert Reply:

The right grease seal for your 2007 Tracker Trailstar Trailer is going to be the Dexter Axle Double Lip Seal for 3,700-lb Marine Hubs item # 168255TB. This seal has an inner diameter of 1.687" and an outer diameter of 2.561".

expert reply by: Jerred H

0

Answer 1

The Replacement Trailer Hub Bearing #15123 and .750 inch outer bearing #LM11949, will use races #LM11910 and #15245. For seals, that inner bearing often is used with the Grease Seals 10-36 (pair) #RG06-070 which have an inner diameter 2.250 inches of…

view full answer...

Answer 2

Since I'm assuming you don't have an E-Z Lube axle or some equivalent with the zerk fitting on the end of the spindle, the only option would be to use a Bearing Buddy. What you have heard about the grease getting pushed out of the back only…

view full answer...

Answer 3

As far as a grease cap goes, I've found one that would work for you. The Fulton #F001524 has an OD of 1.943, which would make for a good compression fit in your hub bore. As far as the seals go, I didn't have much luck. I've looked…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

HI RON! The EcoHitch Hidden Trailer Hitch item #306-X7284 is exactly what you need for your 2011 VW Jetta SportWagen. This hitch fits both the TDI and the gas engine Jetta's. This custom fit hitch has a 2" receiver and has a 2,000 lbs and…

view full answer...

Grease Seal w/ Inner Diameter of 1.687" and an Outer Diameter of 2.561"

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching