Is There a Replacement Jack Screw for Pro Series 12K Jack Leg

Question

Question:

My Pro Series screw looks different than your kit. Pro series has four nuts instead of two pins. Screw stripped after one year with low use. Do you have a replacement?

asked by: David

1

Helpful Expert Reply:

I do have an option for you but we don't offer a replacement jack screw for the Pro Series 12K Square Jacks. Therefore, if yours is faulty then the jack will need to be replaced. For this, we offer the Pro Series Square Jack part # PS1400960376 for with return spring or part # PS1400990376 for without.

expert reply by: Conner L

1

Answer 1

Pacific Rim is the manufacturer of the RAM jacks. You can verify the Replacement Rod and Nut #TJD-12000-RODNUT you found is the correct part by confirming your jack is 3-1/2" by 3-1/2" square and the 1" rod is 17-3/4" long. If you…

view full answer...

Answer 2

Hey Matt we still have that screw kit. It is the Replacement Jack Screw and Nut Kit for Bulldog Sidewind Trailer Jacks item #BD500217. This is designed to fit Bulldog series 182 jacks from 2003 to present with a 12,000 lb capacity. I have linked a…

view full answer...

Answer 3

We may be able to help you find the replacement parts you need for your 12K-rated Fulton jack but a part number for the jack and a photo would help. I did check all 12K-rated jacks and landing gear that we carry and none is the Fulton brand. I did…

view full answer...

Answer 4

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…

view full answer...

Answer 5

If your trailer has 12k capacity Bulldog brand jacks then yes, the part #BD500217 would be the correct part you'd need. If instead they are Bulldog 10k jacks you'd want the part #BD500250 instead.

view full answer...

Answer 6

Hey John, the replacement gear kit you'd need is the part #TJD-12000-RODNUT which I attached two pictures that have instructions and an install diagram.

view full answer...

Answer 7

I went ahead and reached out to RAM and they explained to me that to re-install your inner leg to your RAM jack like the Square Direct Weld Jack - Drop Leg w/ Spring Return #TJD-12000SP-R2NH, you are going to need to re-install the lower pin, replace…

view full answer...

Answer 8

Here is a list of the replacement parts we have for the Ram 12K Support Capacity Jack #TJD-12000SP-F2 you found. Replacement Sidewind Crank #TJD-12000-HD Replacement Plunger Pin Assembly #TJD-12000-PPN Replacement Cap #TJD-12000-CP Replacement Return…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Is There a Replacement Jack Screw for Pro Series 12K Jack Leg

Continue Researching