Will the Additional Width from Slip-Over Rotors Affect the Fit of the Brake Calipers on a Trailer
Updated 02/09/2025 | Published 10/10/2013 >
Question:
I have 2x3 galv axles with idler hubs and want to convert to disc brakes. The dacromet rotors with ss calipers is my choice but I herd that 1/2 inch is added in width when adding the rotors. What happens then with the brake plate found on my axles? Will the pads and caliper alligne?
asked by: Allex
Helpful Expert Reply:
There is some additional width added when using the slip-over rotors like # K2R35DS. This is true on every application that uses this set up. The brackets and calipers are designed for this so they will line up just fine. The wheels and tires will just be 1/2 inch further out on each side.
You will need to make sure that your existing axles have brake mounting flanges in order to add brakes to the trailer. If you do not have a 4-bolt mounting flange on each end of the axle, # 4-35, you will need to have them welded on by a qualified professional with experiencing in adding brake mounting flanges. It is a precision job because the flanges have to be perfectly square and concentric.
I have included a link to an FAQ article that should also help you.
Product Page this Question was Asked From
Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet and Stainless Steel - 3,500 lbs
- Trailer Brakes
- Disc Brakes
- Marine Grade
- 5 on 4-1/2 Inch
- Rotor
- 3500 lbs Axle
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Kodiak
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: lug nuts
- Search Results: brake pads
- Shop: Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet and KodaGuard - 3,500 lbs
- Search Results: axle seal
- Search Results: shorlander
- Search Results: shorelander
- Shop: Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet and Stainless Steel - 3,500 lbs
- Shop: DeeMaxx Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Maxx Coating - 3,500 lbs
- Shop: Replacement Inner Member for Dexter DX7.5L Actuator - Tandem Axle w/ Disc - 2" Ball - 7,500 lbs
- Shop: Dexter Surge Brake Actuator - Disc - Elec Lockout - 2" Ball - Zinc - 7.5K - 3" x 5"
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Shop: Kodiak Trailer Hub for 3,500-lb Axles - 5 on 4-1/2 - Galvanized Steel
- Q&A: Adding Oil Bath Hub and Converting Drum Brakes to Disc On 2021 Grand Design Imagine Travel Trailer
- Q&A: How To Find Correct Replacement Hubs for Skeeter SX2250 Trailer
- Q&A: Cross Reference Chart for Kodiak Trailer Disk Brake Pads to Automotive Applications
- Q&A: What Are The Thicknesses Of The Kodiak 10 Inch Brake Rotor?
- Q&A: How to Determine Correct Over-the-Hub Disc Brakes for Boat Trailer
- Q&A: Will DeeMaxx Disc Brake Kit Fit 2022 ShoreLand'r YAV46TELWMS1-00
- Q&A: Recommended Mounting Hardware for 10" Disc Brakes
- Search Results: trailer brakes
- Search Results: brake fluid
- Video: All You Need to Know About the Kodiak Disc Brakes
- Video: Kodiak Disc Brake Caliper Review
- Video: Complete Breakdown of the Titan Zinc-Plated Brake Actuator w/ Electric Lockout
- Article: How to Bleed Your Trailer Surge Brakes
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision



Remaundo
2/9/2025
hi, if i send you a picture would you be able to tell me what i need far as the bracket, and so forth.