Where In Truck Bed Does B and W Turnoverball Goseneck Install in 2013 Toyota Tundra Short Bed

Question

Question:

What would be the measurement for the 4in hole? Putting in a BandW gooseneck hitch.

asked by: Jose M

0

Expert Reply:

The 4 inch hole that you'll need to drill in the bed of the 2013 Toyota Tundra will be centered from left to right and exactly 42-3/8 inches from the rear edge of the truck bed. This is the location for all bed lengths of your truck as well.

expert reply by: Jameson C

0

Answer 1

If you have a gooseneck trailer then we do have an option for your trailer side with the B&W Extend-A-Goose Gooseneck Coupler #BWTEXA4200. It has a 10" offset and has an outer diameter of 4". For something that site between the hitch…

view full answer...

Answer 2

Yes you can use the RoadActive Suspension Custom Leaf Spring Enhancement Kit #RAS3611-YHD in conjunction with your SumoSprings, however the two may counter each other, so it is recommended to use the lowest setting on the RAS to correct this.…

view full answer...

Answer 3

A sway bar isn't going to help reduce the bounce you've been experiencing with your horse trailer. It sounds to me like you have the PSI level of your air bags either too low or too high. If you don't already have an on-board compressor…

view full answer...

Answer 4

Using these two products together is going to be a little bit of overkill, but I spoke with RoadActive Suspension and they mentioned that as long as your current bump stop (which would be replaced by a Timbren system) sits inboard towards the center…

view full answer...

Answer 5

I took a look at the instructions for both the SumoSprings item #SS45FR and the RoadActive item #RAS4611. They both fit and will work well to reduce squatting or bouncing while towing. You will want to start with the lowest setting on the RAS system…

view full answer...

Answer 6

The air bags I recommend for a 2020 Toyota Tundra are the Firestone Ride-Rite Air Helper Springs part #F2445. The Firestone Air Helper Springs are going to do a great job of helping level the vehicle while loaded or towing which will then improve…

view full answer...

Answer 7

Hello Dejay. So, there are a lot of different features these Air Lift compressor kits offer. While there are other factors that go into pricing, the price is generally a reflection of the features you are getting. For example, on the lower priced end…

view full answer...

Answer 8

Hey Kevin, The Firestone Ride-Rite Air Helper Springs #F2445 are unfortunately not compatible with your B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1257 because it has a mounting bolt right where the spring would need to sit. In…

view full answer...

Answer 9

When installing the Firestone Ride Rite #F2445 with the B&W #BWGNRK1257-5W you won't actually be leaving any bolt holes empty. I've attached an exploded diagram from Firestone that shows the air supply bolt actually has a nut/washer that…

view full answer...

Answer 10

We do offer an Air Lift kit #AL57341 that will Work with an in bed gooseneck hitch like #BWGNRK1020. This is actually the only kit that air lift makes for your truck that is compatible with an in bed hitch. All of it should install relatively easily,…

view full answer...

Answer 11

I do have an option that will allow you to use a set of air springs with a gooseneck hitch however due to the mounting location on your 2008 Toyota Tundra none of our air spring kits including the Air Lift LoadLifter 5000 part #AL88299 will work with…

view full answer...

Answer 12

Lithium batteries really are much nicer than lead acid batteries in terms of how well they hold a charge. There is a much bigger investment required though as the batteries themselves are more expensive you need to use chargers designed for them…

view full answer...

Where In Truck Bed Does B and W Turnoverball Goseneck Install in 2013 Toyota Tundra Short Bed

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching