Will the Demco Recon Work w/ a Rota Flex Pin Box?

Question

Question:

I looked on the Demco website but could not find the answer. I just wanted to make sure the Demco Recon part # DM8550046 is compatible with the Curt Rota-Flex pin box. Thanks

asked by: Chris R

0

Expert Reply:

Yes, you can use the Demco Recon Gooseneck-to-5th Wheel Trailer Hitch Adapter for Recessed Ball item # DM8550046 with a Curt Rota Flex pin box like item # LC328330. The Recon is not compatible with rotating pin boxes but will work great with the Rota Flex.

expert reply by: Jerred H

0

Answer 1

Demco makes a special version of the Recon hitch for flat bed applications that have recessed balls actually! So what you'd want instead is the part #DM8550046. This has a shorter overall height to make up for the additional height of the flat…

view full answer...

Answer 2

Yes, the Demco Hijacker Autoslide 5th Wheel Trailer Hitch w/ Slider, like the 18K #DM8550034 for industry standard beds, will work with the Rota-Flex pin boxes when you use the Capture Plates #DM6171.

view full answer...

Answer 3

A gooseneck adapter cannot be used with the Trailair Rota-Flex 5th Wheel Pin Box - Lippert 1621 - 21,000 lbs #LC328329 because of the excess play and movement that would be present at the connection point. You would instead need to swap out your…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Will the Demco Recon Work w/ a Rota Flex Pin Box?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching