LMX Industrial Strength L11390 Thickener and Viscosity Specs

Question

Question:

What is the thickener type used in the LMX grease L11390? Is it a Litium complex? Also, what is the vicosity index?

asked by: Eric M

0

Expert Reply:

The LMX # L11390 red grease is a lithium complex grease that has a # 2 viscosity index.

expert reply by: Mike L

0

Answer 1

It is acceptable and highly water insoluble so it is great for boat trailers. Grease like the LubriMatic LMX Industrial Strength Grease #L11390 is a lithium complex. The same is true for Lucas Red N Tacky which means they are compatible.

view full answer...

Answer 2

Hello Rodney, thanks for reaching out. The Easy Grease Trailer Hub and Drum Assembly #AKHD-545-35-EZ-K uses a lithium complex grease. This is compatible with a few different greases, but what I recommend is the LubriMatic LMX Industrial Strength…

view full answer...

Answer 3

Hey Mike, Any lithium based multi purpose grease is great to use when packing your hubs. Color does not matter as much as getting the correct type of grease. As long as it is a lithium based multi purpose grease you will be set. Something like…

view full answer...

Answer 4

Hey Tom, so opinions do vary a little bit here and there but both the grease part numbers #L11390 and #L11380 are really nice greases that are going to do very well in the hub of a RV wheel. The 380 is considered to be more of a standard wheel…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

LMX Industrial Strength L11390 Thickener and Viscosity Specs

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching