Bolt Hole Size For Erickson E-Track Tie-Down Anchor # EM37JR Mounting Hardware

Question

Question:

The video stated Grade 5 bolts what is the size of the bolt holes in the flange? Thanks

asked by: Michael

0

Expert Reply:

The Erickson E-Track Tie-Down Anchor # EM37JR has 5/16" holes for the grade 5 mounting hardware. Hardware is not included as you will need to ensure the hardware is the correct length for your application.

expert reply by: Bud M

0

Answer 1

The Erickson E-Track Tie-Down Anchor #EM37JR is 5.2" Long, 5.2" wide and 0.5" tall. The two 5/16" holes are centered on each side of the of the bracket 2.75" from each other. Please see the attached image.

view full answer...

Answer 2

Absolutely, you can mount E track just about anywhere it will fit. We had a customer send in a picture of his E track mounted sided to side on his trailer so the pressure is across all the decking instead of just one board. You can check out the…

view full answer...

Answer 3

The bumps around the edge of the Erickson E-Track Tie-Down Anchor #EM37JR are there to add strength to the flange so that it supports weight better.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hi Wayne, I went out to the warehouse and measured the Caliber D-Ring Anchor Kit part #CA89VT for you. The plate dimensions are 4" long by 3 3/4" wide and the inner diameter of the ring is 1 1/4" and outer diameter is 2 1/4". What…

view full answer...

Answer 6

E-track can be driven over and it will be fine. It would not collapse or otherwise damage itself. You could use and drive over the Erickson Horizontal E-Track #EM19147. Then for a wheel strap the Erickson E-Track Wheel Tie-Down Strap with Roller…

view full answer...

Answer 7

The puck system in the 2022 Chevy Silverado 2500 short bed, is 22-3/8" on center from left to right and 13" top to bottom with a gooseneck hole directly in the center of your bed. I have attached a picture below that will show you them in…

view full answer...

Answer 8

Hi Charles, While we don't currently offer the inner member that you're needing for the UFP A-70 we do offer a compatible replacement with the Dexter DX7.5L A-60 Brake Actuator #DX33FR. This is the entire actuator assembly along with the…

view full answer...

Answer 9

Absolutely! First, in order to hook up to the trailer you will need to add a trailer hitch to your 2020 Ford Transit T150. For this I highly recommend the Curt Class IV #C14012, which features a sleek hidden cross tube design so that only the 2"…

view full answer...

Answer 10

You are correct that we offer both Class III and Class IV 2-inch hitches for your 2018 Ford Transit T350 passenger van. If trailer towing were your intended application then the Class IV hitch #C14012 would definitely be my top recommendation since…

view full answer...

Answer 11

For your 2019 Ford Transit T250 I'd recommend the Curt hitch part #C14012 because it has higher towing capacities but also because it has a mostly hidden appearance since only the hitch opening hangs below the rear bumper. This also helps have…

view full answer...

Bolt Hole Size For Erickson E-Track Tie-Down Anchor # EM37JR Mounting Hardware

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching