Replacement Hitch Threaded Insert for Swagman Chinook Bike Rack

Question

Question:

Does this fit on the swagman chinook?

asked by: Henry C

0

Expert Reply:

For the Swagman Chinook the correct replacement hitch insert is the part # P313. The one you referenced fits other racks.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 3

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 4

It sure will Jim but it will take some modification! The Space Dock 2" Receiver Adapter for Torklift Palomino Landing Pad Bumper item #TLA7900 requires a genuine Palomino Landing Pad bumper. The shaft may need to be shortened to seat properly.…

view full answer...

Answer 5

Hello Andrew, Well that sounds like quite the fun trip, what state or states will you be traveling through? You're asking a really important question, especially since you're planning a cross-country trip with about 250 pounds of bikes and…

view full answer...

Answer 6

Hey Steve! Glad to hear Beaufort Trailer took good care of you with the hitch install. The Benton Shifts&Grins Bike Rack #B54FR is a great choice for your Trek hybrid bikes. It is a nice, solid platform rack with a 55 lb per bike capacity and…

view full answer...

Answer 7

The Replacement Threaded Receiver Insert for Swagman XTC2 Platform Bike Rack #P334 is 3/4" square and 7/8" including the grommet on the end. It sounds like it would be close for what you're looking for.

view full answer...

Answer 8

It looks like you purchased the Replacement Mounting Hardware, #Y8890185. This should have come with the square, black shank insert, a square nut that fits inside of the shank insert, a flat washer, a lock washer and a threaded pin and clip. I made a…

view full answer...

Answer 9

The bolt that comes with the #Y8890185 is the same as the #Y8890176. The bolt is a 1/2"-13 bolt that is 4.28" long with 2.5" of threads.

view full answer...

Answer 10

I do have an option for you but bike rack manufacturers don't publish their hitch pin thread specs to discourage from using a different hitch pin from another manufacturer so this I cannot provide. That said, I can confirm the Locking…

view full answer...

Answer 11

The hitch lock, part #S64029 that you came from for your Swagman Bike carrier should be pretty easy to remove. I have attached a photo of the lock and as the arrow indicates the hitch bolt has a threaded end. After you remove the lock end of the pin…

view full answer...

Answer 12

Hey Ak, thanks for reaching out! The Replacement Anti-Rattle Hitch Bolt and Washer for Yakima HangOver Bike Rack #Y52FR has a 4-5/8" overall length. I've attached a photo of this for your reference. Are you needing to replace the hitch pin…

view full answer...

Replacement Hitch Threaded Insert for Swagman Chinook Bike Rack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching