Diameter of the Axle Brake Grommet 046-016-00

Question

Question:

Can you tell me what the tube OD is of this grommet? Basically what size hole in the axle does the grommet require for ion. I have a AL-KO 3500# axle with a 3/8inch hole. Thanks for all info.

asked by: William G

0

Expert Reply:

The diameter of the Replacement Brake Wire Grommet # 046-016-00 is 3/8" with a length of 7/16". I have attached a video that goes over these measurements at the 25 second mark of the video.

expert reply by: Scott S

0

Answer 1

If you are going to install two of the MORryde X-Factor Crossmembers #MR33WR on your tandem axle trailer Alan you would want to install them on the front and rear hangers. You can install a third one if you want on the middle hanger as well for even…

view full answer...

Answer 2

If you are referring to two white wires from the brake magnet that are coming from the rear of each electric brake assembly, then it would not matter which wire is connected to ground and which wire is used for the brake feed. The magnet that…

view full answer...

Answer 3

Yes, you can use 10 Gauge Wire #10-1-1 to route through your axles to power your Electric Brakes #K23-478-00 Do be sure the Grommet #046-124-00 is in place on your axle tube to prevent the wire from fraying entering the axle tube.

view full answer...

Answer 4

Dexter has confirmed that the #046-124-00 snap in grommet will work with their 7K axles.

view full answer...

Answer 5

This is a common question we get on lights like the LED Trailer Tail Light with License Bracket part #328-003-81LBM1. The original colors you have are the traditional trailer wiring code so brown=taillights, red=turn/brake and white is ground. On…

view full answer...

Answer 6

You'll need a 20 amp circuit breaker for the brake controller power and a 40 amp circuit breaker for the battery charge line circuit from the trailer connector for a total of two. We actually offer a kit with these circuit breakers as well as the…

view full answer...

Answer 7

The replacement snap-in grommet part #046-124-00 that you referenced fits 6,000 lb Dexter axles. If you can verify that you have a 6k Dexter axle this would be the correct fit for it.

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

The reason that 10 Gauge #10-1-1 or 12 Gauge #12-1-1 wire is recommended for 10" brake assemblies, like part #AKEBRK-35-SA, is because they pull more power than the lights on your trailer. I believe the green wire you are referring to carries…

view full answer...

Answer 10

On each individual electric brake magnet the amperage draw would be 3.0 to 3.2 max amps at 12 to 13 volts on 7-inch brake magnets and 3.2 to 4.0 max amps at 12 to 13 volts on 10 and 12-inch brake magnets. The max amperage draw for the brake magnets…

view full answer...

Answer 11

It depends on what the brake controller output is set to. If you have the brake controller set to the maximum then there should be about 12 volts at the brake magnets. To see if the brake magnets are drawing the correct power set the brake controller…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Diameter of the Axle Brake Grommet 046-016-00

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching