Overall Length When Retracted of the Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels

Question

Question:

my trailer has a tongue that is only 23inch in length. I want to know what is the overall length of the Ark Extreme Off-Road Swing-Up Trailer Jack 350d is fully retracted

asked by: Jemail M

0

Expert Reply:

The Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels, # ORJW350D has an overall length of 18".

expert reply by: Michael R

0

Extreme Off-Road Swing-Up Trailer Jack with Dual Wheels
(click to enlarge)

Answer 1

Yes, the Extreme Off-Road Swing-Up Jack w/ Dual Wheels iItem #ORJW500D will work for your T@B 400 Tear Drop Trailer. It looks like your trailer comes with an a-frame jack. You would need to ensure you have enough space on your tongue to accommodate…

view full answer...

Answer 2

From the center of the mounting bracket (Pivot point) to the bottom of the wheels of the Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels - Sidewind - 7" Lift - 770 lbs - Zinc #ORJW350D is 9-1/2" with the jack full retracted, and is…

view full answer...

Answer 3

Filling tires with foam is a fairly common practice for farm or agricultural use, but our tire expert tells me that it's not a recommended practice for trailers that will be operated on paved roads. Once the foam is added to the tire, you've…

view full answer...

Answer 4

Most A-frame campers like your 2019 Aliner Classic off-road model will have a caster wheel tongue jack that uses a hard plastic wheel. There are no replacement pneumatic tires that will fit in place of that wheel but there is a specialty jack product…

view full answer...

Answer 5

The Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels #ORJW350D does not come with the bearings installed. You can use something like a rubber mallet or a block of wood and hammer to tap them into place until they are flush.

view full answer...

Answer 6

The long brackets of the Removable Extreme Off-Road Swing-Up Trailer Jack #ARK57FR that mount on inside of trailer frame are little misleading since they are much taller than the bracket on the other side of the jack that it attaches to. Basically…

view full answer...

Answer 7

The mounting plate on the ARK Removable Extreme Off-Road Swing-Up Trailer Jack #ARK57FR is 5-1/2" wide and 7-1/2" tall. It is designed with several bolt hole patterns(see image) to fit trailer tongues from 2-6" tall.

view full answer...

Answer 8

From the ground to the middle of the mounting bracket for the Extreme Off-Road Swing-Up Jack w/ Dual Wheels #ORJW500D measures 710mm (27.95") when you have it set at the highest setting. This jack gives us the ability to extend the leg using the…

view full answer...

Answer 9

I went out to our warehouse to take a few measurements on the mounting bracket for the ARK Extreme Off-Road Trailer Jack #ORJW350D (compared to the mounting pattern for your existing Fulton F2) and found that they differ enough that you wouldn't…

view full answer...

Answer 10

The Extreme Off-Road Swing-Up Trailer Jack part #ORJW350D would be the best option for an InTech Flyer Pursue Travel Trailer. The weight capacity of said jack is more in-line with the tongue weight of the trailer.

view full answer...

Answer 11

The Ark Extreme Off-Road Swing-Up Jack #ORJW350D fits a wide variety of trailers. The mounting bracket will measure 7-1/2" tall x 5-1/2" wide. The vertical holes are 3/4" apart and the horizontal holes are 1" apart. This makes it…

view full answer...

Answer 12

Hey Rich, that is a really good question. The short answer is, no, you do not need to go relocate your jack. According to the manufacturer, mounting the jack on the middle rail allows it to more evenly distribute the weight of the trailer, making it…

view full answer...

Overall Length When Retracted of the Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching