Installing Trailer Wiring Harness for a 1998 Ford Windstar

Question

Question:

I need an electrical schematic to install the wiring into my 1998 Winstar

asked by: Ron

0

Expert Reply:

The wiring harness for your 1998 Ford Windstar is a plug and play harness, part # C55346. It plugs into your tail light assemblies. I have also included a link to the instructions for installing it on your vehicle.

The 4 pole round connector you were looking at, part # PK11409, can be used instead of the standard flat connectors. The part you were looking at was the trailer end connector. The vehicle end is part # PK11410. You would cut off the flat connector of the wiring harness mentioned above and wire it into the connector. Once the housing of the connector is apart you will see how to wire it. Just make sure positions of the wires on the vehicle connector match those on the trailer connector.

expert reply by: Patrick B

0

Answer 1

For your 2003 Ford E-350 with a step bumper, the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #75703 will fit well. I've attached a photo of a step bumper fit to assist. I've also attached a video install of a…

view full answer...

Answer 2

Yes, the Curt Class III Hitch, part #13407, will fit your 2003 Ford Explorer Sport Trac without removing the factory size spare tire. Spare tires larger than the factory size are not tested with trailer hitches so if your spare is larger than OEM it…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Installing Trailer Wiring Harness for a 1998 Ford Windstar

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching