Correct Replacement for Dexter 010-036-00 Grease Seal

Question

Question:

I currently have the Dexter 010-036-00 seal on my 7000 lbs. axle need to replace them. I believe this is the correct replacement but want to verify that before I purchase. Thank you

asked by: Chris

0

Expert Reply:

Yes, the Grease Seals 10-36 part # RG06-070 are a direct replacement for the Dexter 010-036-00.

expert reply by: Conner L

0

Answer 1

Hi Jeremy; it sounds like the measurement might be slightly off. The #LM67010 is designed to work with the #LM67048 bearing which has a 1.25" inner diameter. It wouldn't be too hard to be off by 0.005" and since you have the race number…

view full answer...

Answer 2

Hi Craig; thank you for providing those part numbers. That is the 2.25" inner diameter grease seal so for replacement bearings you can use the Bearing Kit, LM67048/25580 Bearings, 10-36 Seal #BK3-300 you were looking at. If you prefer Timken…

view full answer...

Answer 3

The MTI number on your 8-201 hubs is simply a casting number. It does not indicate any information about the hubs or have anything to do with the actual part number. I'm not surprised to hear you have different outer bearings between the two…

view full answer...

Answer 4

While there are tire/wheel combinations available using a 235/80r16 tire, you are able to use the tire only #PRG80235 with your existing wheels instead of the wheel and tire combo. As you mentioned you will need to swap out the valve stems to…

view full answer...

Answer 5

I am not 100% sure what you are asking. The newer models of the power centers/converter sections like the Progressive Dynamics 4500 Series RV Converter #PD4590K18LS8 are coming with the switch that you are referencing that allows you to switch…

view full answer...

Answer 6

The Solera Awning Cradle Support #LC289373 does not come with any of the mounting hardware. When installing the support you will want to know where your backer is (such as a stud in the wall). While the support will not be bearing too much of the…

view full answer...

Answer 7

You are correct, the #8-219-4UC3 matches your existing hub and drum assembly. I'm assuming you're referencing the difference in the grease cap when you say the grease is different. This has a standard grease cap, but you can use your existing…

view full answer...

Answer 8

I wasn't able to find anything relating to that part number and since you're unsure of what you have I'd just recommend swapping the entire hub to make everything easier. You're just going to need to choose the hubs that have your…

view full answer...

Answer 9

Thank you for all of the pictures! From the pictures I can tell you that you need replacement brakes #AKEBRK-7R-SA (right hand) and #AKEBRK-7L-SA (left hand), as well as the Dexter Trailer Hub and Drum Assembly #8-219-4UC3-EZ. You might also be in…

view full answer...

Answer 10

It is a very good idea to keep spare bearings and seals (and wheel bearing grease too) on hand for the unexpected roadside stop. We have individual bearing and seal parts like #L68149, #L44649 and #58846 as well as kits like #BK2-100 that combine…

view full answer...

Answer 11

To convert a 5,200 lb Dexter hub to be oil bath all you really need is the kit part #XLPROLUBE2440KIT. This comes with the correct cap and seal as well as the oil needed to make the conversion.

view full answer...

Answer 12

Grease Seal #RG06-050 is the replacement part for the Dexter 010-019-00. It is 1.719 inches inner diameter and 2.565 inches outer diameter. It is a fit for 3500 lb axles. This is a confirmed replacement cross-reference.

view full answer...

Correct Replacement for Dexter 010-036-00 Grease Seal

Product Page this Question was Asked From

Continue Researching