Replacement for WIC 6020 Propane Regulator

Question

Question:

I need to replace my OEM regulator. I understand that there is a JR products one that works, but I cant find it in stock anywhere. I am having trouble finding any regulator available now. Is there anything you have in stock that I could buy to replace the original 6020? If I cant find something soon, my camping season will be over. Thanks in advance.

asked by: Jason B

0

Expert Reply:

The WIC Model 6020 is simply a low pressure two stage automatic changeover regulator from what I can see so you can use many others in its place such as the Camco Automatic Changeover 2-Stage Propane Regulator for Dual Propane Tanks part # CAM59005 which is what I recommend.

expert reply by: Conner L

0

Answer 1

Yes, the Replacement Short Arm Assembly for RV Awnings part #LC404523 is correct for a Solera V000436372 Awning.

view full answer...

Answer 2

You can replace your Dometic 630035.331 condenser units with the Advent Air Replacement RV Air Conditioner for Dometic Setup w/ Start Capacitor - 15,000 Btu #ACDOM150 you were looking at and still retain use of your current air distribution box and…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement for WIC 6020 Propane Regulator

Product Page this Question was Asked From

Continue Researching