Correct Replacement Hydraulic Landing Gear Foot Pad for 2007 Fleetwood Revolution

Question

Question:

I need to replace the foot pads on the rear of my diesel pusher leveling jacks. There is no tagging on the cylinder because of the age. Is there some way I can tell if Lippert part number LC359344 will work on my unit?

asked by: Earl S

0

Expert Reply:

It looks like based on the photo you attached that the Replacement Foot Plate for Lippert Components (LCI) Power Gear Hydraulic Jack part # LC359344 would be the correct replacement foot pad for your Lippert Power Gear Hydraulic Jacks.

expert reply by: Conner L

0

Correct Replacement Hydraulic Landing Gear Foot Pad for 2007 Fleetwood Revolution
(click to enlarge)

Cheryl T.

11/4/2021

What replacement hydraulic landing pad do I need for a 2021 Jayco Greyhawk rear drivers side? Thank you

Les D.

11/8/2021

@CherylT If you can provide me some additional information, we can help you out. First, when you say "landing pad," do you mean just the round flat part where the hydraulic leg touches the ground, or do you mean the entire hydrdaluic leg assembly? If it is just the pad, can you tell me if it is square or round and the diameter/width of it. If it is the entire leg, can you provide me the brand and model number. I'm sure we can get this worked out.

Cheryl T.

11/8/2021

@LesD It is only the round flat part that touches the ground and it is 9 inches. Thank you

Les D.

11/11/2021

If you take a look at the link below it will show you all of our landing gear feet, including the 9 inch round variety. I have also posted links to a few 9 inch rounds.

Helpful Links

dept-pg-accessories_and_parts-pt-jack_foot.aspx

Answer 1

That's a good question but we don't have a way to look that up since Winnebago does not list that as a spec anywhere. You'd have to measure and verify before ordering either the 3 inch #F02-2106 or the larger size #F02-2103. Since the 3…

view full answer...

Answer 2

This is an unexpected configutation with the valve connected directly to the black tank. Nevertheless, it seems that a Valtera #F02-2106 Replacement Rubber Grommet would fix you right up. I think I would spring for some new Valterra #H03-0018 hose…

view full answer...

Answer 3

Since the diameter of the replacement foot pad part #LC359344 that you referenced is 10-1/2 inches the correct SnapPad would be the #SP84FR4.

view full answer...

Answer 4

The bolt does not come with the Replacement Foot Plate for Lippert Power Gear Hydraulic Jack #LC359344. I checked with Lippert, and while there isn't an OEM replacement bolt, they did say that the correct bolt was a Grade 8 3/4"-16 x 1-1/2…

view full answer...

Answer 5

Yes, we do have a replacement foot for the Lippert Replacement Atlas Jack #LC359278 that you referenced as part #LC359344.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Correct Replacement Hydraulic Landing Gear Foot Pad for 2007 Fleetwood Revolution

Product Page this Question was Asked From

Continue Researching