Correct Replacement Motor for Ventline Roof Vent Fan V2062

Question

Question:

I ordered the part BCD0314-00 after searching QandA for the correct replacement of the old Ventline V2062 motor in a 1992 manufactured home. The part is out of stock with estimated shipping Nov 1. The order page says an in stock alternative is BCD0390-01 . My goal is to have as seamless hassle free replacement task as possible. What do I need to do to install the suggested BCD0390-01 that I dont need to do with the BCD0314-00 for the Ventline V2062?

asked by: Gordon C

1

Helpful Expert Reply:

The correct replacement motor for a Ventline Roof Vent Fan V2062 is the Replacement 110-Volt AC Fan Motor for Ventline RV Bathroom Insert Fan part # BCD0314-00. There are no other replacement motor options that will work with this model vent fan.

The listed in-stock alternatives will not work for this application.

expert reply by: Conner L

1

Answer 1

It may not be an exact replacement but there's no reason you couldn't make the #BCD0388-00 fit in place of the smaller motor. They both install in the same way so it would be just a matter of possibly having to drill new holes in the…

view full answer...

Answer 2

For a replacement fan blade for the V2062 you would want the part #BVA0312-00.

view full answer...

Answer 3

The correct replacement motor for your fan is the 110-Volt AC Fan Motor #BCD0314-00 which is 100 CFM capacity.

view full answer...

Answer 4

For a replacement motor for your Ventline V2062 you'd need #BCD0314-00 which also fits as a replacement for the V2262.

view full answer...

Answer 5

Your Philips model V2062 is the same as the Ventline V2062 as Ventline was a division of Philips before they were bought by Dexter. We do have the Replacement 110-Volt AC Fan Motor #BCD0314-00 and Blade #BVA0312-00 that will fit your fan.

view full answer...

Answer 6

For your Ventline V2062 the correct replacement motor would be the part #BCD0314-00. You'll notice it looks very similar to the motor you referenced except it has only two wires like you said you need.

view full answer...

Answer 7

The replacement motor you need for a Ventline roof vent V2062 is the part #BCD0314-00 and for the fan blade part #BVA0312-00.

view full answer...

Answer 8

Yes, the Phillips V2062 and the Ventline V2062 are the same so for a replacement motor you'd need #BCD0314-00. For the replacement fan blades you will need part #BVA0312-00.

view full answer...

Answer 9

Basically either wire can be used as a power wire since the motor can change directions based on which wire has power and ground. What you will want to do is match the power wire of your current setup with the same post as the #BCD0314-00 and it…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Correct Replacement Motor for Ventline Roof Vent Fan V2062

Product Page this Question was Asked From

Continue Researching